problems met skr pro en endstops (no replies)
hi i'm new in marlin en vs code i've built a 3d printer met btt skr pro v1.2 met 2 z leadscrews , 2 extruders and and single endstops.but my endstops don't trigger, what am i doing wrong? in marlin or...
View Article12864 LCD whith ST7565 controller and MKS Robin Nano v1 (no replies)
Hello! I need help. I have LCD module with st7565 controller and I`m tring to connect it to MKS Robin Nano v1.1. I used FSMC connector pins: CS PE12 A0/RS PE10 RESET PE8 SPI2 SCK PB13 SPI2 MOSI PB15...
View Articleesp32(esp3D) WIFI module wont talk to marlin (serial port config?) (6 replies)
I'm working with a BTT SKR-2 motherboard and an esp32u add on board. It is the BTT variety of the add on, but the original firmware (if there was any?) is long gone. I've manage to flash esp3d (3.0)...
View ArticleUpgrading marlin v1.0.0 to v.2.1.2.5 - Z offset to the Bed (no replies)
Hi I have upgraded from the marlin v1.0.0.0 to V2.1.2.5 on the firmware under marlin v1.0.0.0 there is a section below is in rthe configuration.h on v.1 // these are the offsets to the probe relative...
View Articlecan marlin share an SD card via WIFI on skr-2 board (1 reply)
I have an skr2 with an esp32u (BTT) add on wifi module. Got it connected as a simple serial setup, thats fine. But what I would really like to be able to do is send files to the esp32 and have it...
View ArticleMarlin Z-probing in CNC mode (no replies)
Hi, I recently converted my CNC/3d Printer/Laser Engaver machine from repetier to Marlin 2.x Firmware. The thing I cannot get to work is Z probing in CNC mode. I home to Z-Max to prevent colliding...
View ArticleAuto Home - nozzle crashes on platform (no replies)
I have an Anet A8 Plus. When using Auto Homing, the extruder nozzle crashes into the platform. I tried several Marlin generations of the firmware (with the correct corresponding configuration files....
View ArticleReprap belt printers (1 reply)
Hello. I am working on belt printers and would like to 'feel out the community on thoughts, concerns, and ideas about belt printers. Are you considering getting or making one? (If not, reasons?) If...
View ArticleTrinamic current setting (2 replies)
I'm using TMC2209 drivers on a Marlin 2.1.2.4 with my delta printer - and the printer works nice. Question: my current setting X_CURRENT in configuration_adv.h is actually 1200mA, but M122 reports 800...
View ArticleNeed better way to upgrade Marlin (1 reply)
Hi, I just upgraded to Marlin 2.1 from 2.0 and it was all hell set loose. I had to literally go back and start from scratch with Configuration files as there were many things that never matched from...
View Article[Marlin 2.1.2.1] BTT Octopus V1.1 - Issue with controlling fans (no replies)
Hi @all, This is my first post in a forum since 8 years of 3D printing. I have been able to find a solution to all previous problems, but this time I have reached the limit of my knowledge... So, I...
View ArticleMarlin custom gcode - Serial.print gives error during compile (2 replies)
Good day I am trying to add custom Gcode to Marlin. If I remove the Serial.Print the file compile and give the required result however if I include a Serial.print instruction the compiler fail, please...
View ArticleHow do I start printing with a custom Marlin printer? (1 reply)
First let me clarify that I am extremely new to 3D printing. So I was handed down a custom built 3D printer meant to use clay instead of filament. I can get it to move in all directions in the...
View ArticleFirmware 2.1.3-b2. "Probing Point" - digits after the decimal point. (no...
Hello. I have a 3d printer "TronXY 5 SA Pro". When calibrating the bed, when I turn on "Bed leveling" using firmware version 2.1.2.5, an integer and two decimal places are displayed on the "Probing...
View Articlemarlin firmware update - nightmare issue (no replies)
Hi all, just modified my marlin firmware 1.1.9. I can't understand why but I now have weird character on screen and a regular clicking noise on Y axis like if the motor try to start but stay still....
View ArticleConfigure H question (2 replies)
Is the configure h file the same from one version to the next? Can you just keep the same one from version to version if you wanted or do you have to completely re-write it every version? Thanks
View ArticleY axis won't home (no replies)
I re-flashed my Marlin1.1.9 and need some help. My y axis will not home It will start the print where ever it is sitting. If I manually push it onto the endstop it will then move about 15mm off of the...
View ArticleCan't get Babystepping to work Ender-3 PRO 2.0.9.7 (no replies)
Just updated my Ende-3 Pro to the 4.2.7 board and added a BLTouch and a filament runout sensor to it. Working with Marlin 2.0.9.7. Got everything to work fine, but when I edited the FW I enabled...
View ArticleIssues compiling Marlin (no replies)
Hi! I'm having trouble compiling Marlin for Teensy 4.1 board with TMC2209 drivers, BLTouch sensor and DGUS_LCD_UI_RELOADED LCD enabled. I've tried the bugfix version however other new errors pop up...
View ArticleANET A6 Marlin 2.0 (2 replies)
I want to replace my Anet A6 printer card with SKR 1.3 and install Marlin 2.0 but I couldn't. Can someone help me?
View ArticleADVANCED_PAUSE_FEATURE for X,Y,Z move (2 replies)
Hello guys, I would like to ask where can I find this in Marlin version 010109 ? #define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_X_POS 50 // X position of hotend...
View ArticleANET A6 Marlin G28 problem (no replies)
I am trying to setup my printer with Marlin but it is not detecting the endstops during homing. However, I can see the endstops in the terminal. Any suggestions on how I can resolve this?
View ArticleFAN ports confusion with btt skr mini e3 v2 (4 replies)
I must say this is a mind blowing investigation for me. I'm experiencing problems with pwm for fans in ender 3 pro using btt skr mini e3 v2. LCD has two options, one is controller fan, controlled via...
View ArticleBIQU H2 suddenly needs higher value for E-steps (6 replies)
A few years ago I upgraded a Tronxy X5S to a Bigtree SKR v1.3 board and a BIQU H2 extruder. Up until recently it had been working fine. Then one day it started under extruding. Initially I thought...
View ArticleProbe Wizard: Missing reference to based "paper" thickness? (7 replies)
Hello forum community, I've never noticed it before, as I usually set the Z offset by feel. Since I'm changing nozzle sizes more and more often these days, I've gotten into the habit of using the...
View ArticleEnable 12v-pin on board (MKS robinv2.3) (9 replies)
Hello forum community, I want to add an led-strips for my printer by using the 12v-pin ( in photo) on board. But it seems it didn’t work. Do I need to do something, for example, change some settings...
View Articlebltouch G28Z homes only if i run M43 S first (1 reply)
I'm trying to get to bltouch working. I'm running Marlin 2.1.2.2 After reset/power down if I run homing G28 XY homes correctly but there is issue with Z homing: Bltouch probe deploys but compressing...
View ArticleClik here to view.
DGUS Reloaded (no replies)
Hi, I'm unsure if this is in the right place to post, but if not I kindly ask to please move to the right subfolder! I was not sure where to put this as I'm also unsure what the issue here is!...
View ArticleHow will anet a6 acceleration settings be in marlin 2 (no replies)
I installed the Anet A6 type printer SKR 1.3 A4988 driver and installed Marlin 2 but I guess I couldn't make the acceleration settings properly. How can I make the acceleration settings in the safest...
View ArticleTinybee z offset (no replies)
Hello friends, I have a problem, please help me I have a tinybee v1 board, I use Marlin 2.1.2.5 firmware, everything works fine, but my only problem is that no matter how much z offset I give during...
View Article