MULTI_VOLUME on SKR Mini E3 V3 (1 reply)
Hello. I have a custom 3D printer with the following configuration: Motherboard: SKR Mini E3 V3 (https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3) LCD screen: MKS Mini 12864 V3...
View ArticleMKS Robin Nano V1.2 Input Shaping LCD reboot loop? (no replies)
Hi, I have a Ender 3 V1, dropped in a MKS Robin Nano V1.2, and using firmware 2.1.2.1, (I also tried this with the 2.1.2.2 version, still had the same problem). I just learned about input shaping and...
View ArticleSolenoid Tool Clamp (no replies)
Hello to anyone who reads this. I'm new to the forum and came here, of course, to try to solve an issue. I'm a mech eng. so I'm pretty bad at programming (thank God for chatgpt). I have designed a...
View ArticleTemperature range of the UI encoder (no replies)
Hi All, Since a couple of weeks I'm running Marlin on one of my two Ender 3 Pros. I would like to adjust the working of the encoder below the display. If I want to heat the nozzle to change the...
View ArticleGiant custom SCARA - G1 movement issues/inconsistency (no replies)
Hi everyone, I've been working on an issue for days and could really use some help! I've built a custom SCARA printer for a demonstration at an art gallery later this month and it's gone fairly...
View ArticleBLTouch XY Individual Probing Speeds (no replies)
Hello, I am currently setting up a 3D printer with a BigTreeTech SKR3 with Marlin 2.1.0.1 firmware. It is a (really) large printer with a very heavy buildplate and mostly uneven buildplate and...
View ArticleM42 (no replies)
So I finally found the answer to every one of my problems and it's pretty ironic that the answer is 42... Cannot be casual, I guess The only puzzling thing is that although it runs well on its own,...
View ArticleHoming Sequence with extra axis (no replies)
Hello, I'm grappling with a complex setup involving a 3-axis 3D printer with an additional 5-axis component. I'm experimenting with post-processing tasks such as part removal and other functions using...
View ArticleTevoup Tarantula Pro Firmware (2 replies)
Hi folks, I bought a TevoUp Tarantula Pro. * Easy quick assembly. Stock firmware. It wouldn't home properly - X Axis travels all the way to the right seeking the endstop, but endstop is mounted to the...
View ArticleTune menu Bed Z value step (no replies)
Running Marlin 2.1.2 on an Ender 3 Pro, I would like to increase the tuning steps ten fold. Currently the knob increases the Z offset in 1/1000 mm increments, I would like it to be 1/100. Where would...
View ArticleBTT SKR 1.4 - Wanted to use Endstop switch on Z axis and sensor-less homing...
I have BTT SKR 1.4 main board along with TMC2209. I want to use sensor-less home on x and y axis, but on Z axis I wanted to use Endstop switch. Because I don't have BLtouch. Now Easiest solution is...
View Articlehow to configure TMC2209 (1 reply)
Hi there, I recently upgraded my Kossel Mini (Delta) from an Mega2560 to a BTT SKR3 board, with (MKS TMC2209 V2.0) drivers in UART mode, running Marlin 2.1.2.2 - so far with very good results. But I'm...
View ArticleG34 G29 Fail (no replies)
Im having issues with being unable to run the z stepper auto align or a bed leveling. Z Steppers Auto-Alignment - Not Reachable- Recv: Probing Failed and Bed Leveling - (L,R,F,B) out of bounds. The...
View ArticleSKR 1.4 dual z endstop - not moving when homing (no replies)
I recently switched to an SKR 1.4 with TMC2209 on my i3 Mega which has 2 z steppers and endstops. After configuring Marlin 2.1.2.2 when trying to home the z axis doesn't move at all. Octoprint...
View ArticleMarlin 2 Bilinear Auto Bed Leveling (no replies)
Hi Guys. I'm strugling with the bilinear Bed Leveling on my DIY Printer. So in Marlin it says: * - AUTO_BED_LEVELING_BILINEAR * Probe several points in a grid. * You specify the rectangle and the...
View Articleupdate stops at 100% (no replies)
hi, I have Robin nano v3.1 and it works fine with Marlin 2.0.9, but I need input shaping. I created Marlin 2.1.2.2 for my printer and can't update it. The printer starts updating, the status bar...
View ArticleIDEX Tool Change - T1 Crash into T0 (no replies)
Any folks out there with dual x carriage experience have any insights on this issue [github.com]
View ArticlePrinter shutdown when running M48 with large Z probe offset. (no replies)
Hello. I mounted the bltouch on the tip of the nozzle in delta printer, so when I run M48 with Z offset of -47mm, the printer shutdown. When configuring z-47, I changed Z_PROBE_OFFSET_RANGE_MIN in...
View Articlefirmware.bin file size (no replies)
Ok so I have a MKD_SGEN_L V1 in a SWX1 printer. I've obviously flashed firmware to it before with no problems, but now trying to update the firmware to the latest marlin version using my usual board...
View ArticleMarlin: Activate Hotend by using M42 command (no replies)
Hello to all, I am using Marlin to build a CNC machine, not a 3D printer. So far I have been able to fight my way through many problems. But now, the heaters do what they want ;-) I hope someone has...
View Article