Custom command not queued (no replies)
Hey everybody! I create 2 custom commands (M10 & M11) to control a door locking system. Everything works well and I can lock and unlock my door using a out pin. But the command never queued after...
View ArticleUnknown CPU error when updating to Marlin 1.1.3 with MKS Base 1.5 controller...
I spent this evening attempting to update to Marlin v 1.1.3 from the much older version of Marlin that came with my reprap prusa i3. I adjusted all the stock settings accordingly for my machine and...
View ArticleUBL explained please (1 reply)
Can anyone please explain how the grids work in UBL if I have a bed that is X220 by Y270 my probe is behind the hot end by Y+21 and X-5 What points can I use to get the max probe done on those...
View ArticlePreserve UBL Mesh Between Firmware Updates (no replies)
Just curious if there is any way to preserve the UBL mesh values when I update the firmware? I am running the 1.1.x-bugfix branch and that means there are frequent updates, but so far it seems like...
View ArticleNew to Marlin: RAMPS heated bed not working (2 replies)
Just changed over to Marlin (1.1.3) from Repetier on my RAMPS printer as I wanted to try the bed levelling, and can't seem to get the heated bed to power on. The temp reading for the bed works. Bed is...
View ArticleBed leveling and mechanical z endstop (1 reply)
My set up is a mechanical Z endstop and an inductive bed sensor. When X and Y are homed, the inductive sensor is not above the bed, and as such homing Z will not work without a head crash unless I use...
View ArticleManual Mesh Bed Leveling no z endstop (no replies)
hi, is it not possible to do a Manual Mesh Bed Leveling whiteout having a end-stop for the Z axis? because in my tries the extruder did smash in to the bad '-'
View ArticleProblems with Auto Bed Leveling (no replies)
Hi, I try to enable the auto bed leveling feature, but it doesn't works correctly :( I try it with a inductive proximity switch and also with copper wire and an copper plan on the heating bed. The...
View ArticleShort, jerky movements when trying to home with Marlin 1.1.3 (1 reply)
I have upgraded my reprapguru prusa i3 from the old Marlin version that it comes with to version 1.1.3, but my axes will barely move with the new firmware. As far as hardware goes, I have upgraded the...
View ArticleI can not upload marlin to sanguinololu board error avrdude: stk500_getsync()...
Hi any help would be appreciated I am presently running a 3d sprinter setup. I can connect sanguinololu with Pronterface and run 3d Printer on my computer. So hardware/computer connection is OK. I...
View ArticleCan't get Marlin 1.1.x to compile (no replies)
Everyone, I can't get Marlin to compile. I've tried both Arduino IDE 1.6.8 and 1.8.3. I've downloaded a clean copy of Marlin 1.1.x Release version and the only modifications I've made to it where my...
View ArticleExtruder 2 can't reverse turn? (4 replies)
Dear all, Currently I am trying to configure the Marlin for my new machine which has two extruders with one single nozzle. Both extruders can be controlled by Repieter-host, but there is one problem....
View ArticleHow to configure the Marlin for dual extruders (no replies)
Dear All, I have a problem about configuring Marlin for dual extruders. Two of my extruders are exactly same (NEMA 17 associated with 5:1 Geared box). I configured them as same parameters in Marlin...
View ArticleInfo on fw Marlin and Prusa BQ Hephestos XL (no replies)
Hello to all. For a few weeks I bought a BQ Hephestos XL and I'm already printing. I wanted to ask if I can use the original Marwin fw as the electronics is always a RAMPS. Do I guess I only need to...
View ArticleMarlin 1.1.4 : Message Endstops hit missing on G30 (no replies)
Very good days, I have a prusa I3 rework 1.5 and decided to upgrade the firmware from 1.0.2 to 1.1.4. Everything seems to work fine except that when I'm going a G30 I'm not getting the message...
View ArticleGarbled text REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER (no replies)
Hello! I Have built a printer around a Rambo 1.3 and Marlin 1.1.0-RC8, works greate but i have problem with the LCD Randomly it buggs out and displaces the graphics/text. Se pictures, LCDOK is as it...
View ArticleComplies but with errors (1 reply)
Hi all Having a little trouble compiling Marlin 1.1.0 RC7 with IDE 1.8.3 I get the following errors In file included from sketch\MarlinConfig.h:30:0, from C:\Users\Ian\Desktop\3D\CTC...
View ArticlePrinting Above Bed 1.1.4 (no replies)
Hi guys, i hope you can help. I setup my printer with marlin 1.1.4 and BLtouch. The printer homes and then auto levels fine. When it comes to print it is printing above the print bed. When my printer...
View ArticleNew Menu Item to Load / Unload Filament (no replies)
I was surprised to see that there was an option to have a menu item to toggle case led on/off. Cool. I would like to see something similar for Load / Unload filament that basically heats up the head...
View ArticleABL Averaged Probing (no replies)
I recently paired an Anet A8 with a Geeetech BLTouch clone using SkyNet3D (Marlin base). Although accurate most of the time (within 40 microns) it would occasionally be out up to 200 microns. This...
View Article