1.1.x BugFix Crashes On Print (no replies)
Attached is my configuration.h. I upgraded from Marlin 1.1.0-RC8, transfered the settings to the current version. Now when a print job starts, the hotend heats up, the hot bed heats up, the carriage...
View ArticleCan not get firmware working for Wanhao Duplicator i3 with RAMPS1.4 and...
I have been trying to generate firmware for my printer for two days now, and I am about to start pulling out my hair, very frustrated. I have tried the Marlin config tool, editingn manually in...
View Articlemintemp triggered heater_id:0 (no replies)
I have a REPRAP Prusa i3 running Marlin firmware. I just changed the extruder/hotend that came with the kit to a Tital Aero. When trying to print, the heatbed begins to warm up, but the hotend never...
View ArticleMachine never raises Z axis to probe while leveling the bed (no replies)
I have a problem with my recently added inductive probe and Marlin 1.1.9. The probe is connected to the Z min endstop, and works fine for homing. The printer moves in XY to the middle of the bed,...
View ArticleTMC2130 use_tmc_sw_spi driver error (2 replies)
Hi, I've setup everything with tmc2130 to use with spi mode. I did multiple tests that mosi is on pin 44 and able to confirm that I can't use pin 44 because when there's a wire plugged into that pin,...
View ArticleDesperate (no replies)
Hi. I'm new to the forum and 3d printing. I've had my printer a while now, probably about six months (Anycubic Prusa I3 Ultrabase Acrylic). My latest issue has got me completely stumped. My extruder...
View ArticleSD card auto init after boot? (no replies)
Dear all, I upgraded from Marlin 1.1.5 to 1.1.9 and so far all is great except that the SD card, provieded an SD card is inserted, does not auto initialize itself when the printer is reset or...
View ArticleBack off endstops after homing (no replies)
Hi, is there a way to configure marlin to back off the endstops by about ~5mm after homing (all axis)? I'm used to repetier and it has this feature but I couldn't find it on marlin... Thx :)
View Articlemove Z - axis beyond zero without LCD (no replies)
hi , i equipped this week my P802MA (melzi board) with a BLtouch probe. For this i have choose a pin i use normally for the LCD and buttons because there is no other pin left. Bltouch works fine and...
View ArticleMarlin 3d Printer Tool question.. (no replies)
Is anyone familiar with using the "marlin 3d printer tool" ? in the marlin tool, when i go to do the Z-Maintenance, it shows my maximum Z travel as 300mm, when i believe on the tevo tornado, it should...
View ArticleDuet Wifi over extrusion on later change with Slic3r (no replies)
Hi all I recently upgraded to a Duet Wifi board for my core xy printer. I’m running Slic3r 1.2.9 and firmware 1.19 on the duet. At a later change the printer does a large retract followed by an over...
View Articlexy offsets (5 replies)
Marlin 1.1.8 My home is 15mm from edge of bed on x and 8mm from bed on the y Is there an offset in Marlin for this so when I do mesh bed leveling manually it's above my workarea
View Article230v heatbed protection (no replies)
Hello everyone. My printer is equipped with 230v silicon heatbed and I want to make an additiona protection in case of SSR fails I mean is it possible to add an extra code for switch power OFF when...
View ArticleManual mesh bed leveling issue? (1 reply)
Hi! Using an Ender 3 with a warped bed, so I got the TH3D firmware to get mesh bed leveling. I first do corner leveling, test print, repeat until good. Then I do 5x5 mesh level procedure, store the...
View ArticleSTEPS_per_unit (no replies)
Hello fellows, my ,machine uses leadscrew driven system (1cm diameter of leadscrew). I was working with RAMPS + Repetier + 1/32 microsteping and i have set STEPS_PER_UNIT to 4266 according to...
View Articlereprap full graphic controller flickers/ lags when in SD menu (no replies)
I've just "upgraded" my prusa i3 clone from a reprap smart controller to a reprap full graphic smart controller. It seems to work ok (after I've reversed the ribbon cables) but when i select the...
View ArticleHow do I know which line of Gcode my printer is currently executing? (2 replies)
Hi All, I'm writing a custom print host in Python using PySerial, very similar to Printcore but with some added features. Currently, I'm sending line-by-line as I receive the 'ok' back from the board...
View ArticleTMC2130 Sensorless homing with Marlin 1.1.9 and MKS gen 1.4 (no replies)
Hi. I tried to use sensorless homing with tmc2130 via stallguard. So I prepare coreXY frame, 3 X TMC2130, MKS gen 1.4 In the end, X axis and Y axis 's sensorless homing Successfully But Z axis isn't...
View ArticleTrigorilla RAMPS1.3 with LCD and Dual Z-Motor and TMC2130 (no replies)
Goodday, For the last few days I am busy to get my Anycubic printer to work with the TMC-2130 drivers I downloaded the Marlin firmware version 1.1.9. I made the SPI wiring and started with enable the...
View ArticleErrors on fresh install 1.1.9 (no replies)
Hello all, I am attempting to re-flash my new flsun printer( going to cyclops extruder, but that's not the issue). When I download Marlin 1.1.9 and try to compile I receive a ton of errors before even...
View Article