I would like to use an Android tablet to communicate with marlin board(STM32F40 or LPC1768). The physical interfaces of the boards are Type B usb, and the tablet have both USB host and rs232. I have tried both of them, but the board doesn't response.
May I ask if Android can connect with these two marlin boards, and how to do it? Thank you for your attention.

Hi, Anyone using Marlin Power loss recovery with the 1.1.9 Marlin?

The print is resuming after the power loss, but Z-axis is not moving up. It is printing in the same layer where the print was stopped. Z is not going up.
and get home Z first on lcd

Any solutions, please.

Hello everyone, everything good?

I use Creality Ender 3 PRO. I bought the MKS Robin E3 board and managed to install the Marlin firmware normally. However I tried to install the BLTouch sensor together with the firmware and I am not getting success. I found Configuration.h and Configuration_adv.h for the printer. But even so, the BLTouch sensor recognizes, the extraction and retraction commands work, but the PB1 port in Bilinear calibration, at the beginning of printing it does not level with the table and I end up needing to use an Offset Z for each type of height on the table, as if I had manually calibrated it. I followed the tutorial posted by MKS and I couldn't get the sensor to work fully. Follow the wiki: MKS-Robin-E3-E3D - 3D_TOUCH

Another strange thing that my sensor only passed the expansion and retraction test when I inverted the pins S G 5V by 5V G S; and the same thing for PB1; that from S G - I had to change to G S.

Is this wiki really up to date? Does anyone have this card model and could help me in this configuration?

Hi there.
I have tried with the firmware version 2.0.6 and 2.0.6.1 as well with older version that failed to compile with PlatformIO.
I'm using Windows 10 and the platformIO version 1.48.0
Apparently after some updates on the PlatformIO, the compile keep giving same error although the library is inside the project path.

Attached is the configuration.h file which I used that compile with error message attached.

Thanks.

as the title says i cant verify marlin 2.0.x to a arduino Due

[github.com] here it says it supports the due.


DUE version 1.6.12
on the Arduino IDE (1.8.13) i keep getting the error

Arduino:1.8.13 (Windows Store 1.8.42.0) (Windows 10), Board:"Arduino Due (Programming Port)"


In file included from sketch\src\inc/../pins/pins.h:71:0,

                 from sketch\src\inc/MarlinConfig.h:32,

                 from sketch\src\MarlinCore.h:24,

                 from sketch\src\MarlinCore.cpp:31:

sketch\src\inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../core/../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../core/../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\../../core/serial.h:24,

                 from sketch\src\HAL\DUE\DebugMonitor.cpp:25:

sketch\src\HAL\DUE\../../core/../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\HAL.cpp:29:

sketch\src\HAL\DUE\../../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\HAL_SPI.cpp:40:

sketch\src\HAL\DUE\../../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\MarlinSerial.cpp:30:

sketch\src\HAL\DUE\../../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\InterruptVectors.cpp:35:

sketch\src\HAL\DUE\../../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\MarlinSerialUSB.cpp:30:

sketch\src\HAL\DUE\../../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\Servo.cpp:43:

sketch\src\HAL\DUE\../../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

In file included from sketch\src\HAL\DUE\../../inc/../pins/pins.h:71:0,

                 from sketch\src\HAL\DUE\../../inc/MarlinConfig.h:32,

                 from sketch\src\HAL\DUE\Tone.cpp:32:

sketch\src\HAL\DUE\../../inc/../pins/ramps/pins_RAMPS.h:56:6: error: #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

     #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"

      ^

exit status 1

Fout bij het compileren voor board Arduino Due (Programming Port)



Dit rapport zou meer informatie bevatten met
"Uitgebreide uitvoer weergeven tijden compilatie"
optie aan in Bestand -> Voorkeuren.

So as you can see VSCode says NO FIRMWARE FOR YOU ! And shoots me out some computer mumbojumbo I dont understand lol
I need serious help I've been at it for 4 months and everywhere I ask either goes unseen or nobody has a clue of how to remedy this.
I have a SKR Pro v1.1 with TMC2209's I planned on using in my Chiron with its stock LCD but yah I've yet to do so. It does have pretty lights on the board tho..lol
If someone can help me please that would be great !! I've attached my config files and a screenshot of the errors. And will post anything else you may need
Thank You !

I am ready to start the installation of VSCode / PlatformIO venture again!

The first time I installed VSCode / PlatformIO was having problems problems with installing Visual Studio 2017-2019 as the windows registry somehow got really corrupted.
After many windows backups restores determined the the registry had somehow been corrupted about 2 years ago I restored a older version of my Windows 7 Pro.
Have a program that the company has changed owners and therefore will not allow me to reload with all plugins without repurchasing a newer more expensive version.
The previously restored version of Windows 7 Pro has this program plus plugins enact or would re-installed the Windows 10 ver-2004 from scratch.
Have been working on my windows 7 and Windows 10 and all loaded programs for weeks now. Wanted to rebuild my broken registry Windows 7 for Backup.

Would like to install this correctly the first time, when it was installed first time only compile one time them had problems every time after that.
This could have been for many reasons, including the corrupted registry. Though after weeks of restoring would like a finish.

If could learn how to install VSCode / PlatformIO and setup to compile any Marlin 2 from this site should be able to learn from there!!!!!!
Not sure why I am having such big problems with VSCode / PlatformIO for compiling Marlin 2 using Arduino Mega 2560 and Ramps 1.6
Have written programs for many platforms, Operation systems using many computer languages BORLAND, COBOL, FORTRAN ... OMNIS, Visual Studio, to name a few.

Hi folks,

I'm having this wierd issue at the moment with my printer (Wanhao i3 V2, SKR 1.4, TMC 2208 UART @ 1/16, Bltouch, Marlin 2.0.x) where randomly the printer will move double the distance and at twice the speed it is supposed to. Most commonly this happens at the beginning of a print when it is homing the Y axis and mid way through the travel it will speed up. Sometimes however if the bed homes properly the printer will print fine for a while and then appears to randomly double all movements on the Y axis. I have a theory that this might be caused by the Y axis stepper controller losing connection with the board mid print and causing the movements to double but I have no proof for this. Does anyone have any idea what may be causing this or any idea on how to troubleshoot this issue? I've attached my marlin config to this post to help. Thanks in advance.

Hi all,

I have Marlin 1.1.9 and I have an inductive sensor, and I managed to get to this result with G29 P1:

Recv:         0       1       2       3       4       5       6       7       8       9
Recv:  9 | +2.287  +2.817  +2.732  +2.668  +2.622  +2.417  +2.455  +2.257  +2.250  +2.195
Recv:    |
Recv:  8 | +2.242  +2.762  +2.695  +2.630  +2.575  +2.417  +2.455  +2.257  +2.250  +2.195
Recv:    |
Recv:  7 | +2.197  +2.707  +2.657  +2.592  +2.528  +2.425  +2.528  +2.305  +2.387  +2.267
Recv:    |
Recv:  6 | +2.120  +2.670  +2.592  +2.572  +2.512  +2.443  +2.492  +2.330  +2.342  +2.315
Recv:    |
Recv:  5 | +2.105  +2.660  +2.505  +2.562  +2.475  +2.405  +2.457  +2.298  +2.305  +2.260
Recv:    |
Recv:  4 | +2.210  +2.702  +2.542  +2.622  +2.517  +2.410  +2.540  +2.305  +2.298  +2.225
Recv:    |
Recv:  3 | +2.310  +2.673  +2.657  +2.640  +2.550  +2.510  +2.582  +2.347  +2.335  +2.260
Recv:    |
Recv:  2 | +2.265  +2.673  +2.665  +2.640  +2.585  +2.463  +2.552  +2.370  +2.250  +2.207
Recv:    |
Recv:  1 | +2.372  +2.747  +2.707  +2.677  +2.665  +2.492  +2.585  +2.423  +2.298  +2.255
Recv:    |
Recv:  0 |[+2.253] +2.685  +2.653  +2.710  +2.582  +2.467  +2.590  +2.523  +2.312  +2.253
Recv:         0       1       2       3       4       5       6       7       8       9

Based on the documentation and guides available for UBL, I have followed the following sequence:

1. Enabing UBL in the firmware
2. Run G29 P1
3. Then run G29 P3 to fill the blank spots
4. Once I'm done with a good result, I did G29 F10, G29 S1, G29 L1, G29 A
5. Then M500, M501, G28
6. I wanted to show 0 for the z-axis while homed, so I typed G29 P6 Cxx whatever shown on the LCD, then M500, M501, G28 - so that I got 0 for z-axis value
7. I then did the printing height by:
   
   1. Moving the print head to the middle of the bed
   2. Slowly lowering the nozzle until I got it at 0.1mm above the bed
   3. Then again did G29 P6 Cxx whatever number that was showing on the LCD now
   4. M500, M501, then G28
   5. Then tested a few times to make sure it is good
8. In my slicer, I added G29 L1 and G29 A after the G28 command so that the UBL system gets activated.

After all the above, I don't seem to get a good first layer because as you see there is a warp in the bed and I was expecting that the levelling that I've done would correct this however where the warp is, I see the layer line squished and on the opposite side I see it actually thin and not really pushed to the bed.. I tried to observe the z-axis motors to see if any corrections are happening, but they just did not move for the whole first layer..

So is there anything of what I've done above not right? Or it is actually working but my bed is so badly bent that I need to replace it?

Appreciate any inputs or feedback on this!
Regards

Dear all,
I am facing following issues in my Hypercube 3D printer:
1) I am using Hypercube 3D printer. Whenever I prints, my object gets printed as mirrored object.
So I tried to invert directions of X & Y motor. But it won't work. When I inverted directions of motors, I get to know that whenever I move one axis, my nozzel head moves in 2 directions at the same time. which is not correct.How can I resolve this problem?

2) also in pronterface I get message that "Error: volume. init failed" and also sometimes I couldn't print some object of due to memory shortage. That time I reduces the scale of object and then It gets printed. How can I resolve this problem?

3) My display don't works without USB of aurdino connected to the Computer (Even if 12V SMPS is ON). I am using aurdino mega 2560, ramps 1.4 and reprap Full graphics controller.
So as per some people's suggestions I tried to change the 5V IC of aurdino. So I changed that with "AMS 1117 LM1117 5.0 1013 1A " when I changed to this IC my aurdino started heating up and there was burning fragrance in my aurdino. So I again puted my previous IC into aurdino.
So in this case is my IC selection is wrong? What will be the alternative solution to this problem?

4) and my last issue is, earlier my display was showing me memory card into display. But now it is saying"No media".
As soon as I remove memory card it shows message that" media removed" and as soon as I insert it is says "media inserted" but still in options it says "No media"
How this happened?

I am in big problem. Please help me resolving these mentioned problems

Waiting for your prompt response.

Thanks and regards
Vishal

Good Morning!
I have a 3D of my own construction and I use RAMPS 1.4 as a controller.

with marlin 1.1.x it is working well.
When I update FW to 2.0.6 I start having problems with auto leveling.

I send the command to level, he starts leveling and on the x-axis he starts not to make the correct movements as if he were missing steps and ends up going off the table.

And random time is correct and time is lost.

Returning to FW 1.1.4 it starts to work normally.

Another problem I have is the heating of the hotend I can't heat more than 220 degrees, someone can give me a hint how I can increase this limit.

TKS

Hello Everyone,

I have bought a board to add it to my custom 3d printer.

MKS Gen L V1.0 Board.
MKS Gen L V1.0 Picture

and i received it without a stepper drivers XD

i bought DRV8825 right now.

I have changed the stepper driver in marlin from A4988 to DRV8825 and i uploaded the marlin to the board.

NOW, do i need to change anything else? im sorry but im toooo young for this coding bla bla bla XD

but at least im trying to do something.

I hope if somebody can support me as usual from this forum.

Thanks a lot

Marlin 2.0.7

Hello all,
I have the Tevo Tornado 2018 gold edition printer. This printer used the MKS_Gen_L 1.0 board and A4988 Green version stepper driver chips. I upgraded this printer to a E3D v6 Gold hotend and a Zesty Nimble v1.2 Direct Drive system. I also upgraded my PWS to a MeanWell PWS. Edited and upload Marlin 1.1.x bugfix version to the printer. Board ype in the Configuration.h file is the BOARD_MKS_GEN_L I then tried just moving the printhead in each of the 3 axis X, Y, Z. I had to reedit the Configuration.h file to correct the direction of the motors. I have that fixed. I then tried homing my printer. During an auto homing G28 the print head goes to the left until it hits the min endstoip for the X direction. Then it goes to the Y min direction. Then it goes on a diagonal direction where it stops at the center of the bed. On my printers LCD display it shows X150, Y150, Z0. I tried moving the printhead to X0, Y0, Z0 which is the left front of my printer.. I first turned of the Endstops off with a M211 S0 command. And I did a M428 to set the home position offset. I did a M500 to save. Then a M211 S1 to turn Endstops back on. Then I tried a G28. The printer still homes to the middle of the print bed. Lastly, I tried from the LCD display a Home X, then Home Y, then Home Z. Home X moves the head to the X0 position. Home Y moves the print head to the Y0 position, left front. Home Z moves the printhead on a Diagonal direction to the center of the printbed. I am not quite sure what I am doing wrong or if there is a bug in the marlin firmware.

Any help will be appreciated,

John

hi all

tried my luck at the pronterface forum- alas, no luck there…….

need help here- Pronterface keeps shutting down my " prints" after 3 cycles, motors move normally- with the KILL message:

Print started at: 19:08:14
echo:busy: processing
echo:busy: processing
echo:busy: processing
Errorrinter halted. kill() called!
[ERROR] Errorrinter halted. kill() called!

application is CNC
have dummy thermocouple 998/999 on tried various settings
commented out various temp controls:

MARLIN:
#define TEMP_SENSOR_0 999
//#define TEMP_SENSOR_1 0
//#define TEMP_SENSOR_2 0
//#define TEMP_SENSOR_3 0
//#define TEMP_SENSOR_4 0
//#define TEMP_SENSOR_BED 0
//#define TEMP_SENSOR_CHAMBER 0

// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 0
#define DUMMY_THERMISTOR_999_VALUE 0

// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
// from the two sensors differ too much the print will be aborted.
//#define TEMP_SENSOR_1_AS_REDUNDANT
//#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10

// Extruder temperature must be close to target for this long before M109 returns success
//#define TEMP_RESIDENCY_TIME 10 // (seconds)
//#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
//#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.

// Bed temperature must be close to target for this long before M190 returns success
//#define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
//#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
//#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.

// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
//#define HEATER_0_MINTEMP 5
//#define HEATER_1_MINTEMP 5
//#define HEATER_2_MINTEMP 5
//#define HEATER_3_MINTEMP 5
//#define HEATER_4_MINTEMP 5
//#define BED_MINTEMP 5

// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
//#define HEATER_0_MAXTEMP 275
//#define HEATER_1_MAXTEMP 275
//#define HEATER_2_MAXTEMP 275
//#define HEATER_3_MAXTEMP 275
//#define HEATER_4_MAXTEMP 275
//#define BED_MAXTEMP 150


also:
//#define PREVENT_COLD_EXTRUSION
//#define EXTRUDE_MINTEMP 170

/**
* Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
* Note: For Bowden Extruders make this large enough to allow load/unload.
*/
//#define PREVENT_LENGTHY_EXTRUDE
//#define EXTRUDE_MAXLENGTH 200


//#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
//#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed


endstops are ok

keep getting the ^*^*TT*&!!! error message!

help very much appreciated

thx!

C

i just added piezo probe to my tronxy x5s . nozzle homes about 20mm left of bed, thats normal position. when i try to probe the bed with nozzle it tries to probe in 0,0 coordinates. tried every setting that gives some offset or distance from edge, nothing works. any ideas?

Hello, I have an MKS SBASE 1.3 board with Marlin 2.0 running ok.
The problem that I'm having is that the network port on the board is not working with Marlin, juts for testing, I have installed Smoothiboard, and network port works just fine, so discard board/hardware problems

I'm guessing that it's a confiuration issue, the USB port works fine, but the ethernet port on the board is blinking when connect a network cable, any Ideas?

I upgraded from Marlin 1.9.x to 2.0.7.
- I am using an Einsy Rambo with integrated TMC2130 drivers. I literally used the same currents from the 1.9.x version on the 2.0.7 and the motors barely have strenght to move.
- How is this possible? Is the new marlin managing current in a different way?

I am using stealthchop on both versions.

XYZ Current 700
E0 Current 800

Those values are the same on both 1.9.x versions and 2.0.7.

Cheers,
JJ

also in pronterface I get message that "Error: volume. init failed" and also sometimes I couldn't print some object of due to memory shortage. That time I reduces the scale of object and then It gets printed. How can I resolve this problem?

3) My display don't works without USB of aurdino connected to the Computer (Even if 12V SMPS is ON). I am using aurdino mega 2560, ramps 1.4 and reprap Full graphics controller.
So as per some people's suggestions I tried to change the 5V IC of aurdino. So I changed that with "AMS 1117 LM1117 5.0 1013 1A " when I changed to this IC my aurdino started heating up and there was burning fragrance in my aurdino. So I again puted my previous IC into aurdino.
So in this case is my IC selection is wrong? What will be the alternative solution to this problem?

4) and my last issue is, earlier my display was showing me memory card into display. But now it is saying"No media".
As soon as I remove memory card it shows message that" media removed" and as soon as I insert it is says "media inserted" but still in options it says "No media"
How this happened?

I am in big problem. Please help me resolving these mentioned problems

Waiting for your prompt response.

Thanks and regards
Vishal

Hello Everyone,

I am hoping to find some answers to why I cannot compile firmware for this setup. Starting with this fork of the Marlin Bug-fix-2.0.x firmware made by SwiftNick - Full Chiron Support

In short I am getting some warnings relating to undefined references in anycubic_tft.cpp and anycubic_chiron_lcd.cpp.
My experience level is novice when it comes to programming, or I would probably be making sense of this.

Using vscode and platformio to compile the firmware. I believe I managed the config.h, config_adv.h, and all the pins files for the SKR 1.4 Turbo correctly.
Not certain if there is a way to bypass strict mode? This may not be advisable I am guessing. Just wanting to get some testing done of basic systems on the printer, I don't necessarily need the touch screen but ultimately want it working.

I am using Linux Mint 19.1 Cinnamon version 4.15.0-66-generic and believe I am not missing any dependent libraries or so I think.

Any and all help is appreciated, thank you very very much.

Here is a log from the terminal: note: I did catch this warning and resolve it in a previous attempt "this 'if' clause does not guard... [-Wmisleading-indentation]"
I believe it was a tab being used instead of the proper spacing to indent.





~/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x$ platformio run -e LPC1769 ; echo "done" >/tmp/ipc
Processing LPC1769 (platform: [github.com]; board: nxp_lpc1769; framework: arduino)
--------------------------------------------------------------------------------------------------------------------
Verbose mode can be enabled via `-v, --verbose` option
CONFIGURATION: [docs.platformio.org]
PLATFORM: NXP Arduino LPC176x (0.1.3) > NXP LPC1769
HARDWARE: LPC1769 120MHz, 31.97KB RAM, 464KB Flash
DEBUG: Current (cmsis-dap) On-board (cmsis-dap) External (blackmagic, jlink)
PACKAGES:
- framework-arduino-lpc176x 0.2.5
- toolchain-gccarmnoneeabi 1.90301.200702 (9.3.1)
Converting Marlin.ino
LDF: Library Dependency Finder -> [bit.ly]
LDF Modes: Finder ~ off, Compatibility ~ strict
Found 2 compatible libraries
Scanning dependencies...
Dependency Graph
|-- 1.0.0
|-- 0.7.1
Building in release mode
upload disk: /media/magoose/A87B-A154/
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/DebugMonitor.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/HAL.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/HAL_SPI.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/MarlinSerial.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/eeprom_flash.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/eeprom_sdcard.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/eeprom_wired.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/fast_pwm.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/include/digipot_mcp4451_I2C_routines.c.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/include/i2c_util.c.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/main.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/tft/tft_spi.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/tft/xpt2046.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/timers.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/u8g/LCD_I2C_routines.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/u8g/LCD_pin_routines.c.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_hw_spi.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_ssd_hw_i2c.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_sw_spi.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/usb_serial.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/LPC1768/watchdog.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/HAL_spi_L6470.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/backtrace.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/unwarm.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/unwarm_arm.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/unwarm_thumb.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/unwarmbytab.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/unwarmmem.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/unwinder.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/backtrace/unwmemaccess.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/eeprom_api.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/eeprom_if_i2c.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/eeprom_if_spi.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/esp_wifi.cpp.o
Compiling .pio/build/LPC1769/src/src/HAL/shared/servo.cpp.o
Compiling .pio/build/LPC1769/src/src/MarlinCore.cpp.o
Compiling .pio/build/LPC1769/src/src/core/serial.cpp.o
Compiling .pio/build/LPC1769/src/src/core/utility.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/babystep.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/bedlevel/bedlevel.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/bedlevel/mbl/mesh_bed_leveling.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/cancel_object.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/caselight.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/leds/neopixel.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/pause.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/powerloss.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/runout.cpp.o
Compiling .pio/build/LPC1769/src/src/feature/tmc_util.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/bedlevel/G42.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/bedlevel/M420.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/bedlevel/mbl/G29.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/bedlevel/mbl/M421.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/calibrate/G28.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/calibrate/G76_M192_M871.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/calibrate/M666.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M200-M205.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M220.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M221.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M301.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M302.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M304.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M575.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M672.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/config/M92.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M108_M112_M410.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M111.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M120_M121.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M17_M18_M84.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M211.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M226.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M280.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M350_M351.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M380_M381.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M400.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M42.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M80_M81.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M85.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M993_M994.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M997.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/M999.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/control/T.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/eeprom/M500-M504.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/advance/M900.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/cancel/M486.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/digipot/M907-M910.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/pause/G27.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/pause/M125.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/pause/M600.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/pause/M603.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/powerloss/M1000.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/powerloss/M413.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/runout/M412.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/trinamic/M122.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/trinamic/M569.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/trinamic/M906.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/feature/trinamic/M911-M914.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/gcode.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/geometry/G92.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/geometry/M206_M428.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/host/M110.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/host/M113.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/host/M114.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/host/M115.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/host/M118.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/host/M119.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/lcd/M0_M1.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/lcd/M117.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/lcd/M145.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/lcd/M300.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/motion/G0_G1.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/motion/G2_G3.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/motion/G4.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/motion/M290.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/parser.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/probe/G30.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/probe/M401_M402.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/probe/M851.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/queue.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M1001.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M20.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M21_M22.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M23.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M24_M25.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M26.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M27.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M28_M29.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M30.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M32.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M33.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M34.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M524.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/sd/M928.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/stats/M31.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/stats/M75-M78.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/temp/M104_M109.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/temp/M105.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/temp/M106_M107.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/temp/M140_M190.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/temp/M141_M191.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/temp/M155.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/temp/M303.cpp.o
Compiling .pio/build/LPC1769/src/src/gcode/units/M82_M83.cpp.o
Compiling .pio/build/LPC1769/src/src/lcd/extui/anycubic_chiron_lcd.cpp.o
Compiling .pio/build/LPC1769/src/src/lcd/extui/lib/anycubic_chiron/FileNavigator.cpp.o
Compiling .pio/build/LPC1769/src/src/lcd/extui/lib/anycubic_chiron/Tunes.cpp.o
Compiling .pio/build/LPC1769/src/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp.o
Compiling .pio/build/LPC1769/src/src/lcd/extui/ui_api.cpp.o
Compiling .pio/build/LPC1769/src/src/lcd/fontutils.cpp.o
Compiling .pio/build/LPC1769/src/src/lcd/touch/touch_buttons.cpp.o
Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp: In member function 'void Anycubic::ChironTFT::PanelAction(uint8_t)':
Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp:587:9: warning: this 'if' clause does not guard... [-Wmisleading-indentation]
587 | if (printer_state == AC_printer_resuming_from_power_outage)
| ^~
Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp:591:11: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'if'
591 | injectCommands_P(PSTR("M1000\n")); // home and start recovery
| ^~~~~~~~~~~~~~~~
Compiling .pio/build/LPC1769/src/src/lcd/ultralcd.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/BL24CXX.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/W25Qxx.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/buzzer.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/crc16.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/hex_print.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/nozzle.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/numtostr.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/stopwatch.cpp.o
Compiling .pio/build/LPC1769/src/src/libs/vector_3.cpp.o
Compiling .pio/build/LPC1769/src/src/module/endstops.cpp.o
Compiling .pio/build/LPC1769/src/src/module/motion.cpp.o
Compiling .pio/build/LPC1769/src/src/module/planner.cpp.o
Compiling .pio/build/LPC1769/src/src/module/probe.cpp.o
Compiling .pio/build/LPC1769/src/src/module/servo.cpp.o
Compiling .pio/build/LPC1769/src/src/module/settings.cpp.o
Compiling .pio/build/LPC1769/src/src/module/stepper.cpp.o
Compiling .pio/build/LPC1769/src/src/module/stepper/indirection.cpp.o
Compiling .pio/build/LPC1769/src/src/module/stepper/trinamic.cpp.o
Compiling .pio/build/LPC1769/src/src/module/temperature.cpp.o
Compiling .pio/build/LPC1769/src/src/module/tool_change.cpp.o
Compiling .pio/build/LPC1769/src/src/sd/Sd2Card.cpp.o
Compiling .pio/build/LPC1769/src/src/sd/SdBaseFile.cpp.o
Compiling .pio/build/LPC1769/src/src/sd/SdFatUtil.cpp.o
Compiling .pio/build/LPC1769/src/src/sd/SdFile.cpp.o
Compiling .pio/build/LPC1769/src/src/sd/SdVolume.cpp.o
Compiling .pio/build/LPC1769/src/src/sd/cardreader.cpp.o
Compiling .pio/build/LPC1769/libbd9/Servo/Servo.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/CHOPCONF.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/COOLCONF.cpp.o
Archiving .pio/build/LPC1769/libbd9/libServo.a
Indexing .pio/build/LPC1769/libbd9/libServo.a
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/DRVCONF.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/DRVCTRL.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/DRVSTATUS.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/DRV_CONF.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/DRV_STATUS.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/ENCMODE.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/GCONF.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/IHOLD_IRUN.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/PWMCONF.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/RAMP_STAT.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/SERIAL_SWITCH.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/SGCSCONF.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/SHORT_CONF.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/SMARTEN.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/SW_MODE.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/SW_SPI.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMC2130Stepper.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMC2160Stepper.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMC2208Stepper.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMC2209Stepper.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMC2660Stepper.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMC5130Stepper.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMC5160Stepper.cpp.o
Compiling .pio/build/LPC1769/lib853/TMCStepper/source/TMCStepper.cpp.o
Compiling .pio/build/LPC1769/CMSIS/driver/debug_frmwrk.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_adc.c.o
Archiving .pio/build/LPC1769/lib853/libTMCStepper.a
Indexing .pio/build/LPC1769/lib853/libTMCStepper.a
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_can.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_clkpwr.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_dac.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_emac.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_exti.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_gpdma.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_gpio.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_i2c.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_i2s.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_iap.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_libcfg_default.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_mcpwm.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_nvic.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_pinsel.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_pwm.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_qei.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_rit.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_rtc.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_spi.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_ssp.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_systick.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_timer.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_uart.c.o
Compiling .pio/build/LPC1769/CMSIS/driver/lpc17xx_wdt.c.o
Compiling .pio/build/LPC1769/CMSIS/lib/chanfs/ff.c.o
Compiling .pio/build/LPC1769/CMSIS/lib/chanfs/ffunicode.c.o
Compiling .pio/build/LPC1769/CMSIS/lib/chanfs/mmc_ssp.c.o
Compiling .pio/build/LPC1769/CMSIS/lib/chanfs/rtc176x.c.o
Compiling .pio/build/LPC1769/CMSIS/lib/usb/cdcuser.cpp.o
Compiling .pio/build/LPC1769/CMSIS/lib/usb/mscuser.cpp.o
Compiling .pio/build/LPC1769/CMSIS/lib/usb/usbcore.cpp.o
Compiling .pio/build/LPC1769/CMSIS/lib/usb/usbdesc.cpp.o
Compiling .pio/build/LPC1769/CMSIS/lib/usb/usbhw.cpp.o
Compiling .pio/build/LPC1769/CMSIS/lib/usb/usbuser.cpp.o
Compiling .pio/build/LPC1769/CMSIS/system/startup_LPC17xx.S.o
Compiling .pio/build/LPC1769/CMSIS/system/system_LPC17xx.c.o
Compiling .pio/build/LPC1769/lpc176x/HardwarePWM.cpp.o
Compiling .pio/build/LPC1769/lpc176x/SoftwarePWM.cpp.o
Compiling .pio/build/LPC1769/lpc176x/pwm.cpp.o
Archiving .pio/build/LPC1769/libCMSIS.a
Indexing .pio/build/LPC1769/libCMSIS.a
Compiling .pio/build/LPC1769/FrameworkArduino/CDCSerial.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/HardwareSerial0.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/HardwareSerial1.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/HardwareSerial2.cpp.o
Archiving .pio/build/LPC1769/liblpc176x.a
Indexing .pio/build/LPC1769/liblpc176x.a
Compiling .pio/build/LPC1769/FrameworkArduino/HardwareSerial3.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/Print.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/SoftwareSPI.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/SoftwareSerial.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/Stream.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/Tone.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/WInterrupts.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/Wire.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/arduino.cpp.o
Compiling .pio/build/LPC1769/FrameworkArduino/main.cpp.o
Archiving .pio/build/LPC1769/libFrameworkArduino.a
Indexing .pio/build/LPC1769/libFrameworkArduino.a
Linking .pio/build/LPC1769/firmware.elf
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/anycubic_chiron_lcd.cpp.o: in function `ExtUI::onStartup()':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/anycubic_chiron_lcd.cpp:40: undefined reference to `Anycubic::Chiron'
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/anycubic_chiron_lcd.cpp.o: in function `ExtUI::onIdle()':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/anycubic_chiron_lcd.cpp:42: undefined reference to `Anycubic::Chiron'
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/anycubic_chiron_lcd.cpp.o: in function `ExtUI::onPrinterKilled(char const*, char const*)':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/anycubic_chiron_lcd.cpp:45: undefined reference to `Anycubic::Chiron'
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/anycubic_chiron_lcd.cpp.o: in function `ExtUI::onMediaInserted()':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/anycubic_chiron_lcd.cpp:48: undefined reference to `Anycubic::Chiron'
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/anycubic_chiron_lcd.cpp.o: in function `ExtUI::onMediaError()':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/anycubic_chiron_lcd.cpp:49: undefined reference to `Anycubic::Chiron'
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/anycubic_chiron_lcd.cpp.o:/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/anycubic_chiron_lcd.cpp:50: more undefined references to `Anycubic::Chiron' follow
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp.o: in function `Anycubic::ChironTFT::SendFileList(signed char)':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp:407: undefined reference to `Anycubic::filenavigator'
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp.o: in function `Anycubic::ChironTFT::SelectFile()':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp:429: undefined reference to `Anycubic::filenavigator'
/home/magoose/.platformio/packages/toolchain-gccarmnoneeabi/bin/../lib/gcc/arm-none-eabi/9.3.1/../../../../arm-none-eabi/bin/ld: .pio/build/LPC1769/src/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp.o: in function `Anycubic::ChironTFT::PanelAction(unsigned char)':
/home/magoose/Full-Chiron-Support-SKR1.4T-bugfix-2.0.x/Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp:703: undefined reference to `Anycubic::filenavigator'
collect2: error: ld returned 1 exit status
*** [.pio/build/LPC1769/firmware.elf] Error 1
=========================================== [FAILED] Took 148.58 seconds ===========================================