hi at all...
i have an problem with my delta,is 2 week im change parameter without solutions....
im use a Marlin-2.0.x on my delta
these are my problems:
1:) the sd not work ,same gcode on usb work,but with usb not work,tft not look nothing....im want install on it the picture on the link ,im know if i not have a robin version,but im not undestand where download that picture for the "not robin version"
2:) the temperature is set form cura at 210,the machine arrive at 210...212...204...208....206...210...212...214...212...208...206...30 min in this condition....
3:) the bed leveling....i have a bed on glass,im think is not necessary make a grid with more and more point,but im think,for me is a first experience with this ,not know.
for me is not a problem make a calibration of 5 point of bed ony one print...
at moments the machine after heating nozzle and bed, go near the bed with probe out,make one taste on x- y- square,go up,pause few seconds and when it start to print,go down the bed and demage glass.... but he make only one taste....im think set up of one point....
other problem is setup cura to make a preview and write a start of gcode of item to print,im not know if i have write all perfect...
this is the start :
at the moments i have a driver DRV8825 but i have buy from aliexpress a TMC2209 im think install them when arrived me.
I have look if the TMC2225 are new,but im not look a documentation if they work with these version of board ,you know ??
Sorry for more question and more problem,but im write the complete my situation.....thanks a lot for patience with me...
im from italy and im go to work,im answere at all your question when im come back to home...
i have an problem with my delta,is 2 week im change parameter without solutions....
im use a Marlin-2.0.x on my delta
these are my problems:
1:) the sd not work ,same gcode on usb work,but with usb not work,tft not look nothing....im want install on it the picture on the link ,im know if i not have a robin version,but im not undestand where download that picture for the "not robin version"
2:) the temperature is set form cura at 210,the machine arrive at 210...212...204...208....206...210...212...214...212...208...206...30 min in this condition....
3:) the bed leveling....i have a bed on glass,im think is not necessary make a grid with more and more point,but im think,for me is a first experience with this ,not know.
for me is not a problem make a calibration of 5 point of bed ony one print...
at moments the machine after heating nozzle and bed, go near the bed with probe out,make one taste on x- y- square,go up,pause few seconds and when it start to print,go down the bed and demage glass.... but he make only one taste....im think set up of one point....
other problem is setup cura to make a preview and write a start of gcode of item to print,im not know if i have write all perfect...
this is the start :
M104 S{material_print_temperature_layer_0} T0 ; set extruder temperature.
M109 S{material_print_temperature_layer_0} T0 ; set extruder temperature and wait for temp.
G21
G90
M107 ;VENTOLE OFF
G28 ;Home
G29 ; BLTouch Bed Leveling-----
G92 E0
G1 E2 F800
G92 E0
G1 F(travel_speed)
M117 In stampa...
at the moments i have a driver DRV8825 but i have buy from aliexpress a TMC2209 im think install them when arrived me.
I have look if the TMC2225 are new,but im not look a documentation if they work with these version of board ,you know ??
Sorry for more question and more problem,but im write the complete my situation.....thanks a lot for patience with me...
im from italy and im go to work,im answere at all your question when im come back to home...