2.0.X bugfix does not homing on delta properly + DUE USB communication -...
Hello, I have problem on Z tower when homing delta, it does not do bump. On X and Y tower it works fine. Same issue was reported in Marlin 1.1.x, and it was solved in later release, but it looks in...
View ArticleTemperture limit with commands M104/M109 different from screen limit (no...
Hello, I got this problem and I'm unable to find a solution by myself. I want to set up the hotend temperature up to 300 degree but the firmware limits the commands M104 and M109 returning a max...
View ArticleCan two Z probes be used with different controller pins? (no replies)
The printer I am working on at the moment has two different Z sensors, one of which is a touch sensor used for bed leveling and the second of which is a single under-bed sensor used to find the...
View ArticleSetting Probe Speed (no replies)
I have Marlin 2.0.7.2 installed on an Anycubic Predator delta. I have the "pause for deploy/stow" function turned off in configuration.h as I am using a permanently mounted piezo sensor under the bed....
View ArticleMarlin 2.0 leveling bed corners (no replies)
I have a Two Trees Sapphire Plus printer. The print bed is 310x310mm with a printable area of 300x300mm. The printable area is centered on the print bed. The physical endstops leave the print head at...
View ArticleInitial layers 'squish' wrong direction. (no replies)
I'll try and explain what I mean. tronxy X5, Marlin bugfix 2, but had same problem with 1.9 Bed auto levels, using BIQU level senor. Glass tronxy bed Z homes to the middle of the bed. 3 x 3 grid. rear...
View ArticleTrouble with BLTouch and homing (1 reply)
So a few years ago I built a prusa clone back when everyone was using ramps1.4 and arduino ide to compile firmware. Things ran fine for years and then I sorta took a break from everything 3d printing....
View ArticleDelta + MKS Sgen L V 1.0 + tft35 v1.0 + bltouch (no replies)
hi at all... i have an problem with my delta,is 2 week im change parameter without solutions.... im use a Marlin-2.0.x on my delta these are my problems: 1:) the sd not work ,same gcode on usb...
View ArticleInstalling Marlin on Weedo F100 Mini 3D Printer. (no replies)
Hi, I have a Weedo F100 Mini 3D Printer, which was also sold as a Festnight F100 Mini or Funtastique EVO 3D Printer, and I would like to install Marlin firmware on the controller. I looked up the...
View ArticleIntermittent Relay Temperature (no replies)
I changed the board of the Monoprice MIni v1 for Arduino Mega 2560/ramps 14.. everything is working perfectly, but the relay flashes when it reaches the extruder temperature. What can I do in...
View ArticleAuto bed leveling not auto leveling please help. (no replies)
I have build a new printer with the spec below but it won't auto level properly. The Z screw moves on the first layer but its like it's doing it in reverse to what it needs too. I have checked and...
View ArticleAUTOTEMP (1 reply)
Anyone have experience with AUTOTEMP in configuration_adv.h I want to be able to reduce the hot-end temperature if the print speed drops below a certain speed (like below 10mm/s). From the comments in...
View ArticleIs there a command? (2 replies)
I have 4 Z stepper motors. Is there a command that I can move just one motor? The reason why I want to do this is because, Z3 will not move. The brake turns on (Z3) when i try to move Z axis. All...
View ArticleMarlin on RasPi Pico (1 reply)
I'm working on putting this new micro to work. The platform is a modified Anycubic Linear Plus with a 3-in-1-out extruder. I spun a custom board for it, to connect the RasPi to the components. I...
View Articleender 3 pro marlin bed not centered (no replies)
So I'm trying to flash the marlin firmware on my ender 3 pro with an skr mini e3 V2.0 everything compiles and flashing the firmware onto the printer goes fine, but when I home it the bltouch is not...
View ArticleTMC2209 Error with Tevo Tornado V2 using latest Marlin firmware (12 replies)
Hi all, so several weeks back I successfully built Marlin firmware when I installed MakerbaseTMC 2209 v2 drivers on my Tevo Tornado and everything was working fine. Well a few days I decided to use...
View ArticleRecommended thermistor to reach a bit over 300*? (no replies)
Hello, I'm working with marlin on a customized CR10s. With the original board and firmware 1.x I was able to reach 300* (of course with a microswiss hotend). Then I installed an SKR 1.3 and upgraded...
View ArticleErrors on Configuration files (no replies)
Hi all, in 2.0.7.2 there is the file motion.cpp that has instructions you can see in motion.png attached but in all configuration.h of all files downloaded from here there is the declaration you can...
View ArticleNeed some help, new to modifing firmware (1 reply)
Ok, So I am new to the 3D printing world (about 6 months) and this is my first attempt at doing my own firmware, I have had a horrible time trying to figure out if I am doing everything right, but I...
View ArticleFixing systematic X-carriages twist for auto bed levelling (no replies)
Hi, like others, I had a systematic issue with an x-carriage twist on my Anycubic Mega S, running Marlin 1.1.9 and a BLTouch V3.1 probe sensor. It yielded in a tilt of my auto-levelling mesh and in...
View Article