Flas / Ram requirements for Marlin 2.0 (no replies)
Hello i have an simple questions as in other forum question an argument exist that the r73 Borad with STM32F103vet6 MCU has to less Ram to make a Marlin 2.0 port. So could anyone share his knowledge...
View ArticleSeparate filament load/unload value for each extruder (no replies)
Hi! I’m building a tool changer 3D printer with 4 different hot ends, and they need different load/unload lengths on filament change. If I set a value in configuration_adv.h for...
View ArticleSAMD51 with BTT TFT24 V1.1 (no replies)
Hello sir, I am using Adafruit Grand Central M4 with Ramp board on top in my 3D printer So I want to use BTT TFT24 V1.1...
View ArticleMore than one toolheads with more than one Z probe types (no replies)
I made a Hypercube EVO 3D Printer. I have three toolheads: - Filament printing head (integrated BLTouch) - Laser engraving head (integrated BLTouch) - Plywood cutter (Drill head) for wood works ( X )...
View ArticleWrong temp reading on heater sensor (2 replies)
I have a DIY printer with Marlin 2.0, an Arduino MEGA 2560 and a RAMPS 1.4. It has two of the same temperature sensors in it that read differently by about 11 degrees. If the bed reads about 20...
View ArticleSKR 1.4 3Dtouch Pin wont deploy (2 replies)
Hey all, Cant do any Z homing on my new BTT SKR 1.4, cant get the pin to deploy, just moved over from a MKS GEN L, was working fine. Used the same pins basicly Z_MIN and the Servo on the SKR. Does a...
View ArticleIs there a simple way to get just the inductive probe status? (2 replies)
I would like to just test the Z-axis inductive probe (for example by holding an Allen wrench under the probe) and get feedback to my BTT TFT43 display that the inductive probe is triggered. I know I...
View ArticleReading TMC Stepper Driver actual current (no replies)
I know you can set the TMC current with the M906 command and you can read if you have a "prewarn" condition if the driver is getting too hot with the M911 command. But can you read the actual current...
View ArticleClik here to view.
4 Extruder on IDEX mode (2 replies)
First tests of 4 extruders on IDEX [www.thingiverse.com] [www.youtube.com] 4EX2.jpg
View ArticleVSCode compilation issues of marlin 2.x bug fix (1 reply)
Hello everyone, I'm here because I was referred from the Marlin Github page because I am having a user-support issue and not a bug. I won't dwell on this as it's a waist of time, energy and really not...
View ArticleConfiguring Marlin for mystery board (no replies)
Hello all, Recently got my hands on a 3D printer board pulled from Shenzhen (photos attached). I've been wanting to use them for a project, but the provided firmware is a horribly mangled version of...
View ArticleFEEDRATE for IDEX tool change (no replies)
Hi, Is it possible to set the speed (FEEDRATE) for changing tools T0 / T1 in IDEX mode?
View ArticleMarlin Bugfix(2.0.X) Duplicate Problem Don't Working (no replies)
Hi I have a problem Dublicate Mode. Did you have Cura setting for duplicate Mode Idex is working but dublicate dont work extruders.. first of all I sent G28 and M605 S2 X250 R0 after that heaters and...
View ArticleFirmware 2.2.x compiling error (no replies)
Hi all, I am trying to compile the Marlin firmware 2.2.x version. I know about the Arduino IDE linking error related to long filenames, so I am using the Arduino CLI "Nightly" version. Also running...
View ArticleStrange extruder motions (no replies)
Hello all,, I have changed the extruder of my Tevo Tarantula and had to change the direction of the stepper motor in the the firmware. Just changed the CHANGE_E0_DIRECTION define in a firmware 1.1.x...
View ArticleEEPROM question-Marlin (no replies)
Hello Folks. I realize this is a newbie question. I thought I understood at first but I'm now getting confused about how EEPROM really works on a 32bit board (MKS Robin Nano - STM32F106...) Could...
View ArticleAttempting to open menu freezes LCD (1 reply)
Hello all, I've been trying to port Marlin to a STM32F106RET6 board I have for a project. I've been able to compile and upload firmware to the board, and at this point I seem to have everything...
View ArticleReset to factory settings (no replies)
Hello I didn't feel like a newby but I just cant get My Geeetech A20M to print. I flashed the firmware with a couple different versions from GitHub. I added a 3d touch to help me with bed leveling and...
View ArticleEnder 5 Pro - Configuration intrigue (1 reply)
Hello everyone, I've tried looking for information regarding my "issue" to no avail. I have an ender 5 Pro with the stock 8bit board, flashed with Marlin 2,0 BF and pretty much everything is bone...
View ArticleI get "Heating Failed: E1 PRINTER HALTED" when reaching target temperature...
Hello, This has been happening since I installed an SKR1.3 board, with marlin 2.0. Just when the hotend is about to reach the target temperature it triggers the error. This happens randomly. If it...
View Article