ABL issue with 2.1.x bugfix and bltouch (no replies)

I have been having issues with inconsistent fist later. The middle of the build plate tends to be find, but the outside corners are too thin. The print comes out the same with ABL on and off. I have confirm the mesh is updating in the EEPROM. I have confirmed everything is mechanically tight and probe offset is accurate. I have even bought another bltouch. I'm at a loss and looking for suggestions.

Recv: Cap:SERIAL_XON_XOFF:0
Recv: Cap:BINARY_FILE_TRANSFER:0
Recv: Cap:EEPROM:1
Recv: Cap:VOLUMETRIC:1
Recv: Cap:AUTOREPORT_POS:0
Recv: Cap:AUTOREPORT_TEMP:1
Recv: Cap:PROGRESS:0
Recv: Cap:PRINT_JOB:1
Recv: Cap:AUTOLEVEL:1
Recv: Cap:RUNOUT:1
Recv: Cap:Z_PROBE:1
Recv: Cap:LEVELING_DATA:1
Recv: Cap:BUILD_PERCENT:0
Recv: Cap:SOFTWARE_POWER:0
Recv: Cap:TOGGLE_LIGHTS:0
Recv: Cap:CASE_LIGHT_BRIGHTNESS:0
Recv: Cap:EMERGENCY_PARSER:1
Recv: Cap:HOST_ACTION_COMMANDS:1
Recv: Cap:PROMPT_SUPPORT:1
Recv: Cap:SDCARD:1
Recv: Cap:MULTI_VOLUME:0
Recv: Cap:REPEAT:0
Recv: Cap:SD_WRITE:1
Recv: Cap:AUTOREPORT_SD_STATUS:0
Recv: Cap:LONG_FILENAME:0
Recv: Cap:LFN_WRITE:0
Recv: Cap:CUSTOM_FIRMWARE_UPLOAD:0
Recv: Cap:EXTENDED_M20:0
Recv: Cap:THERMAL_PROTECTION:1
Recv: Cap:MOTION_MODES:0
Recv: Cap:ARCS:1
Recv: Cap:BABYSTEPPING:1
Recv: Cap:CHAMBER_TEMPERATURE:0
Recv: Cap:COOLER_TEMPERATURE:0
Recv: Cap:MEATPACK:0
Recv: Cap:CONFIG_EXPORT:0
Recv: ok
Send: M21
Recv: echo:SD card ok
Recv: ok
Send: M155 S2
Recv: ok
Send: M876 P1
Recv: ok
Send: M20
Recv: Begin file list
Recv: End file list
Recv: ok
[...]
Send: M503
Recv: echo:; Linear Units:
Recv: echo: G21 ; (mm)
Recv: echo:; Temperature Units:
Recv: echo: M149 C ; Units in Celsius
Recv: echo:; Filament settings (Disabled):
Recv: echo: M200 S0 D1.75
Recv: echo:; Steps per unit:
Recv: echo: M92 X80.00 Y80.00 Z400.00 E97.07
Recv: echo:; Max feedrates (units/s):
Recv: echo: M203 X500.00 Y500.00 Z5.00 E25.00
Recv: echo:; Max Acceleration (units/s2):
Recv: echo: M201 X500.00 Y500.00 Z100.00 E1000.00
Recv: echo:; Acceleration (units/s2) (P R T):
Recv: echo: M204 P500.00 R500.00 T1000.00
Recv: echo:; Advanced (B S T X Y Z E):
Recv: echo: M205 B20000.00 S0.00 T0.00 X10.00 Y10.00 Z0.30 E5.00
Recv: echo:; Auto Bed Leveling:
Recv: echo: M420 S0 Z10.00 ; Leveling OFF
Recv: echo: G29 W I0 J0 Z0.00450
Recv: echo: G29 W I1 J0 Z0.00050
Recv: echo: G29 W I2 J0 Z-0.04150
Recv: echo: G29 W I3 J0 Z0.01150
Recv: echo: G29 W I4 J0 Z0.01300
Recv: echo: G29 W I0 J1 Z0.12600
Recv: echo: G29 W I1 J1 Z0.09700
Recv: echo: G29 W I2 J1 Z0.07200
Recv: echo: G29 W I3 J1 Z0.10300
Recv: echo: G29 W I4 J1 Z0.11700
Recv: echo: G29 W I0 J2 Z0.15550
Recv: echo: G29 W I1 J2 Z0.11800
Recv: echo: G29 W I2 J2 Z0.10450
Recv: echo: G29 W I3 J2 Z0.14300
Recv: echo: G29 W I4 J2 Z0.11200
Recv: echo: G29 W I0 J3 Z0.13200
Recv: echo: G29 W I1 J3 Z0.08700
Recv: echo: G29 W I2 J3 Z0.04850
Recv: echo: G29 W I3 J3 Z0.08900
Recv: echo: G29 W I4 J3 Z0.06200
Recv: echo: G29 W I0 J4 Z0.06200
Recv: echo: G29 W I1 J4 Z0.04450
Recv: echo: G29 W I2 J4 Z-0.00150
Recv: echo: G29 W I3 J4 Z0.02950
Recv: echo: G29 W I4 J4 Z0.00550
Recv: echo:; Material heatup parameters:
Recv: echo: M145 S0 H185.00 B45.00 F255
Recv: echo: M145 S1 H240.00 B70.00 F255
Recv: echo:; Hotend PID:
Recv: echo: M301 P34.61 I4.37 D68.54
Recv: echo:; Bed PID:
Recv: echo: M304 P142.75 I26.63 D510.09
Recv: echo:; LCD Brightness:
Recv: echo: M256 B250
Recv: echo:; Power-loss recovery:
Recv: echo: M413 S0 ; OFF
Recv: echo:; Z-Probe Offset:
Recv: echo: M851 X-47.00 Y-4.40 Z-2.18 ; (mm)
Recv: echo:; Filament load/unload:
Recv: echo: M603 L0.00 U0.00 ; (mm)
Recv: echo:; Filament runout sensor:
Recv: echo: M412 S1 ; Sensor ON
Recv: ok