Problema con Kossel mini (no replies)
Salve a tutti ragazzi, ho un problema con una kossel mini su cui ho montato una ramps e un arduino (cinese ovviamente). Ho provato a caricare questo firmware [github.com] e non funziona come dovrebbe,...
View ArticleMarlin 1.1 RC8 reboots after bed reaches temps (1 reply)
I installed the latest Marlin RC8. All the setups when fine. When I start printing, the bed heats up. Once it reaches the set temps and the extruder is supposed to start heating the software reboots.
View ArticleX and Y axis skips forward before auto bed leveling.?! (1 reply)
I recently upgraded my lead screws and one motor to a Nema 23. Before the upgrade I had things pretty dialed in. And after the upgrade I only remember changing some speed settings and steps per mm....
View ArticleLooking for some help understand a ZMIN ENDSTOP issue. (2 replies)
Hello, I have a almost finished Hypercube (corexy) printer. Ramps 1.4, Mega2560 with Marlin 1.1.0-RC8. I have a proximity sensor mounted near the hotend. I don't actually have a hot end installed yet,...
View ArticleFull graphics display wont work (no replies)
Hello i have some very wird issus. First i have a Creality 3D Afinibot A9 printer, it is a very fine one, and it fit my need. i have now startet to add some extensions on it. the first thing is that i...
View ArticleFull Graphics display on Megatronics v3.1 (1 reply)
Greetings, I have a new Megatronics v3.1 with a Graphics Display LCD with controller and SD card reader. The board is working fine as is the LCD as I've put both through the their respective test...
View ArticleBed Levelling on RC8 working but not compensating (1 reply)
Hi, I am trying to set up bed levelling with RC8, I have a Z Probe on the Z Min stop. Everything works fine, Homing to Z fine, G29 fine, G29 reporting looks fine, but when I actually try a print then...
View ArticleCompletion percentage on full graphic lcd (no replies)
Hi, Is there an option in Marlin to show the completion percentage on the full graphic lcd? It shows a progress bar only which is less predictable. Thanks
View ArticleBitte um Hilfe! Fehler beim kompilieren Marlin RC8 (no replies)
Schönen guten tag ich hänge jetzt seit tagen beim kompilieren fest und verstehe einfach nicht was der fehler sein soll da ich nicht genau weis was ihr noch an infos braucht fragt bitte einfach ich...
View ArticleAdjusting Marlin for quite printing (no replies)
Hi guys My printer make some disturbing noises when prints the contour of the object and the first layer. Something goes into resonance and start vibrate. This happend at any speed but at lower speeds...
View ArticleProblems with autolevel (no replies)
My autoleveling seems a bit off and can't get it to function correctly. I tried raising the matrix to 5x5 but same result. After a G29 if I go to X200 Y200 Z0 I have a .2 gap between nozle and bed. If...
View ArticlePossible to set "ZMin" when doing bed leveling / Z probing (1 reply)
Question: Can a "ZMin-while-probing" be set? Meaning a minimum Z height the printer bed can move to, while Z Probing. Purpose: For safety reasons should the probe switch not fire for some reason. --...
View ArticleG code for calibration (4 replies)
This is my code for adjusting my bed. But after cleaning nozzle process my printer suddenly set extruder temp to 0. Why is that? What is wrong? G21 ;metric values G90 ;absolute positioning M82 ;set...
View Articlecustom menu options with multiple lines of G-Code (2 replies)
Marlin has no documentation. I would like to add load/unload scripts and a manual level script to my menu system on my Kossel. I tried it with the original firmware that Folger provided, and I...
View ArticleThere maybe a problem for ST7920 initial in ultralcd_st7920_u8glib_rrd.h (no...
Dear sir, I had tried a new LCD module which use other one LCD controller that compatible to ST7920. I got a problem about the initial code @ uint8_t u8g_dev_rrd_st7920_128x64_fn(u8g_t *u8g, u8g_dev_t...
View ArticleNeed a little help understanding the M163 G-code. (no replies)
How does weight correspond to a color. How do you calculate the P value for a color. Using R, G, B how do you calculate P where Saddle Brown uses R = 139, G = 69 and B = 19 So what would the...
View ArticleLCD X and Y position (1 reply)
Hi, Do you know how can I disable from Marlin the position of X and Y when it's not printing and also when it's printing? I really don't need them and they just fill the place for nothing on my LCD....
View ArticleStrange timings in source code (no replies)
Hello! I decided to look at the code to understand how things work in multistepping and found some thing which bother me :) Don't judge me too hard please and excuse me if i a blind and do not see...
View ArticleIssues with y direction in corexy (1 reply)
Hey guys, I have been struggling with getting my corexy printer running on a ramps board with marlin installed. The old controller was a closed source one from chitu3d but even after triple checking...
View Articleconnecting second z-stepper-motor (no replies)
Hi all! I'm a bit of a newbie, been printing for a while, then my board stopped working. So I replaced my Arduino 2560 + Ramps 1.4 Shield for this MKS, and of course I need to install Marlin on it....
View Article