SKR Mini E3 V3 and MKS Mini 12864 V3 SD card problem (2 replies)
Hello. I'm building a custom 3D printer and facing a strange problem with the LCD SD card reader. The problem is that the LCD freezes when I click on "Print from media". Motherboard: SKR Mini E3 V3...
View ArticleMarlin responding differently to pronterface commands vs SD card gcode (4...
Been testing my ATMega256 marlin laser engraver with pronterface, and all the motion commands work, and things like G0 S200 X60 Y60 will move the head and also activate the laser for the entire...
View Articleups and auto shutdown (5 replies)
Hi guys I have two controller,a BTT GTR V1.0 and a MKS ROBIN NANO V3 can I use ups module(power lose recovery) and auto power off after print is done module for the both boards at the same time?
View ArticleMarlin 2 - RAMPS - Can't get 4th axis to enable stepper (5 replies)
Using BOARD_RAMPS_14_SF on MEGO2560 I axis pins are defined instead of the original E0 axis. The E0 axis has pins defined as -1. The stepper does not enable. Sending a force state to the enable pin...
View ArticleX5SA (no replies)
Bonjour, les capteurs inductifs et capacitifs ont de gros problèmes avec la température! Par exemple les capteurs de proximités pour les avions (entre 20 et 25000€ et je ne parle pas de la puce...
View ArticleError - duplicate offset (1 reply)
The error occurs when moving the axes, leveling or printing a gcode, the displacement is incorrect, since the movements are increased by double, for example, if I give X displacement in 10 mm, it...
View Articlebrauch Hilfe beim zweitem Extruder (no replies)
Hallo Leute, ich habe irgendwie Probleme mit meinem Drucker und zwar ich habe 2 Extruder und 2 düsen wenn ich jetzt bei cura alles so einstelle das er alles in schwarz drucken soll ( E1) druckt er...
View ArticleCreality V2.2 and DGUS LCD Config (1 reply)
I want to build Marlin from scratch for my setup which is an FYSETC DGUS LCD and my Creality V2.2 motherboard (MEGA2560) I bought LCD here: [www.aliexpress.com] I'm using Marlin V2.1.1 but when I...
View ArticleSKR Mini E3 V3 firmware update question (2 replies)
Hello. I've built a 3D printer with the following configuration: Motherboard: SKR Mini E3 V3 (https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3) LCD screen: MKS Mini 12864 V3...
View ArticleBigTreeTech SKR Mini E3 2.0 keine Verbindung zum PC, Abnullen (1 reply)
Hallo liebe Leute mein U20 Board war abgeraucht. Habe es durch ein BigTreeTech SKR Mini E3 V2.0 -und dem BT TFT35-E3 V3.0 Touchscreen- ersetzt. Habe eine Marlin 2.1.1 per SD Karte draufgespielt. Die...
View ArticleCan't understand how laser mode is supposed to work (1 reply)
Hello. I converted ender 3 to control my diy laser module, it uses XYENABLE pin to control it with pwm. Original X and Y steppers enable have been pulled down to ground with 100k resistor so it works...
View ArticleAutomatic Bed Probing vs Automatic Bed Leveling (no replies)
So I got an error in compiling Marlin: #error "Disable PREHEAT_BEFORE_LEVELING when using PREHEAT_BEFORE_PROBING." I have no idea why these two should conflict with each other. It raises a question...
View ArticleCustom firmware name (no replies)
Hi all, thank you fir a great forum! I am thinking of trying to swap out the control board on my raise3d pro2 plus. I have bigtreetech sk3 with the same processor as the original board so I hope the...
View ArticleShowing µC workload (2 replies)
Hello, I'm planning to connect this 4.0inch SPI Module ST7796 to my printer. My SKR2 has a stm32f429vgt6. Is that µC powerful enough to do the task and still working reliable to control the printer? I...
View ArticleShow live Z while Tramming (1 reply)
Hi, I'm not much of a programmer but I've been trying to change the menu screen to display a live z position while trimming. I think it'd be useful. Could someone point me in the right direction? I...
View ArticleBoard Version for Ender 5 Pro (no replies)
So I'm trying to update my ender 5 pros firmware to marlin 2.1.1 and I've already got ardunio and the marlin config files ready to verify but when I go to verify the files in Arduino It keeps giving...
View ArticleMarlin with Ramps 1.4 discount smart controller and Max6674 (no replies)
Sorry for maybe being a bit noob on this, but I have a ramps 1.4 a reprap discount smart controller and a Max 6675 thermocouple amplifier. I am looking for info how I can hook up the Max 6675 on the...
View ArticleLooking for Help (no replies)
I have a kinda sorta RepRap 3d printer I think. It is running Marlin 2.1 with a Arduino 2560 and Ramps 1.4. Also has the 12864 Display along with bltouch.. The software will load, but in so doing it...
View ArticleSafe homing not working with Knutwurst Marlin (no replies)
So I recently build the BFPTouch and installed it on my Anycubic Mega S. For the Z probe I am using the Z min endstop pin. I configured Knutwurst Marlin like it was described in the Video and...
View ArticleUnknow message on terminal (no replies)
Hi, I just compiled my own version of Marlin 2.1.1 for my Alfawise U30 Pro printer. The build seems to work fine except that I keep getting a message on the Octoprint terminal. I don't know what is...
View Article