Bed Tramming Marlin Code (no replies)
I've been trying out the Bed tramming feature and I have found that it works good but I would like to change the way it does the tramming to make it more accurate. are there any programmers out there...
View ArticleFr accented characters not recognized by the screen (no replies)
Hello, Another question. I have a display problem on the LCD screen of my Alfawise U30 Pro (DGUS_LCD_UI_RELOADED). I use French language and the accented characters (é, è, ê,...) are not recognized by...
View ArticleMarlin Ramps 1.4 filament replacement or loading issue (no replies)
Hi community, I own the printer that I assembled myself. Ramps 1.4 arduino atmega 2560. I installed Marlin 2.x, everything seems fine now, but when I give the commands to load filament from the...
View ArticleClik here to view.
fighting with M808 Loop (no replies)
Hi everybody, I'm trying to make a 45° extension module to make little infinite printing just when I need it. see : Youtube Short : Marlin 2.1.x M808 loop 337px-GA3Dtech45deg.jpeg I've a few problems...
View ArticleStruggling possibly drowning.. (no replies)
I have been setting up Marlin 2 on a BTT Mini E3V2 and not getting far. I have everything moving in the right direction and homing into the correct corner, the heaters and fans all work the PiD tunes...
View ArticleFilament Change M600, extrude a little bit material after resume to print...
Hello I have troubles with the M600 filament change function. After reload filament, i clean the nozzle to be pretty clean. If it looks well, i press continue and the nozzle will resume to the last...
View ArticlePULSE XL FIRMWARE ERROR (3 replies)
I am trying to configure the MATTERHACKERS PULSE XL firmware located at the following site: [github.com] The source code does not compile and I have found most of the bugs except one. It will not...
View ArticleG29 Issue (1 reply)
Hi all, I'm looking for help with a UBL issue on 2.0.5. Start gcode includes: G29A G29 L1 G29 J This causes the machine to do a complete UBL bed probe -- 121 points -- which takes a long time. The UBL...
View ArticleBTT SKR MINI E3 V3.0 Cannot compile marlin - Motherboard not defined (1 reply)
Hey everyone, Having an issue trying to compile marlin for the SKR Mini E3 V3.0 Printer - Creality Ender 3 V2 It states that the motherboard is not defined, yet clearly it is. Have been using the...
View ArticleFilament Change id TFT (no replies)
Hello friends Tell me which parameter in the configuration is responsible for the length of the retraction \ extrusion of the rod when changing the maryan from the tft menu? In my case, the Flying...
View ArticleStep signals for Z motor (1 reply)
I was viewing the step signals of Z motor on an oscilloscope and found that the signals were just of a 10 percent duty cycle and were very less in number compared to what the required steps per mm...
View ArticleDual Z axis will move together, but will not home together (no replies)
Originally posted this to the marlin bugfix, but they locked the post and said that is would be better way to get support for a user issue from the forum. So I'm here. Below is the original post,...
View ArticleCancelling a print. (no replies)
I've built a [not a 3D printer] that uses Marlin as its control engine. I'm using octoprint as host software. Just now a "print" went wrong and I hit "cancel". Octoprint stops sending new commands,...
View ArticlePrinter will not Home Needing Help (no replies)
This is a new posting of a problem that I started by saying Help Needed. I have worked this down to where a gentleman by the nave of Dust has been helping me. He asked for a video of my problem of...
View Articlemks pwc (no replies)
Hi friends I have a mks robin nano V3.1 with ts35 v2.0 LCD,I want to install mks pwc on It but I faced with this error while mks robin nano V3.1 supports pwc module,is there any way to solve this error?
View ArticleLCD problem in Marlin 2.1.1 (no replies)
hi everyone, I need help, I'm using version 2.1.1, and after I installed the self-leveling servo, my lcd gives an error and I can't use it anymore, this only happens when the servo is triggered,...
View ArticleMks Mini 12864 v3 Portrait orientation? (1 reply)
Hi there, I have an Afinia H480 3d printer and I have spent on it way more than I should. As you can see in the photo attached, I'm looking to mount the LCD on the vertical, I've managed to rotate it...
View ArticlePIDTEMP calibration (1 reply)
Hello Hello everybody, I have a DELTA KOSSEL K800XL I change original board to a SKR1.3+TMC2226 (TMC2209) I use marlin 2.1.x I try to calibrate PIDTEMP and PIDTEMPBED. I use pronterface to do it :...
View ArticleY axis endstop at max issue (no replies)
Hello, I am building a custom cartesian 3d printer and trying to get the new marlin version 2.1.1 running but seem to be running into an issue. Printer: basic dual extruder running a Ramps 1.4 with...
View ArticleTeensy 4.1 will not read bed temperature (no replies)
Hello, I've recently started constructing a custom 3d Printer driven by a Teensy 4.1 and in my initial attempts to flash marlin I have run into an issue detailed below. Any help would be greatly...
View Article