Step Motor Speed at Microstepping (no replies)
Hello, First of all thank you for Marlin software I am using MKS Robin Nano v3.0 card I am controlling Step Motor (Nema 17 0.47 Nm) My Step motor driver card is TMC2209 Steps Per unit for Z axis is...
View ArticleDual Extruder Marlin Configuration Help (1 reply)
Repurposed old printer CubePro Duo frame. Replaced all electronics. Using BTT SKR 1.4 Turbo with TMC 2209 drivers, TFT35 screen, and BL Touch. Also added heated bed. Issue: I believe I have Marlin...
View ArticleTwo Z axis stepper motors (no replies)
Hello, I have marlin 2.1.2.1 and Iam building my own 3d printer. I want to controll dual Z axis stepper motors with two drivers. Iam using arduino with ramps 1.6. The second Z2 driver is pluged into...
View ArticleZ-offset Calibration lost. head "sinks" during Z-Offset calibration. (no...
First up, I'm a noob. so apologies for missing knowledge. Kit Tronxy XY-2 Pro running latest version of Marlin firmware 2.1.2.1 2003-05-16. Slicer Ultimaker 5.4.0 Too long to read Z-offset Calibration...
View ArticleSuper weird - Marlin SD print stutter when not connected via serial (1 reply)
Hello, this is my first post here. I have used Marlin for years, ran into countless problems, but this one is new to me... Long story short(ish), my printer ran fine. It's got a RAMPS 1.4, Arduino...
View ArticleIs Geeetech i3 Pro compatible with Marlin 2.1 (2 replies)
Is Geeetech i3 Pro compatible with Marlin 2.1 ? I use 1.9 today but curious to try 2.1 ! Tanks :-) Ola A. in Sweden.
View ArticleG29 causes Z motors to stall on Marlin 2.x (2 replies)
Coming from Marlin 1.1.8, I tried to move over to Marlin 2.0.9.x but got an irratic behaviour of G29 on lineair bed leveling.All normal moves go well until G29 tries to lift Z 15 milimeters higher...
View ArticleEnder3 v4.2.7 BIQU v2 microprobe setup? (1 reply)
HI all, I'm trying to configure marlin for a BIQU v2 microprobe on an ender 3 with a v4.2.7 board. I have made my way through the "MicroProbe V2 user manual" and I think I have marlin all configured...
View ArticleTrying to make ABL for rotary engraver (1 reply)
Hi, I recently built a rotary laser engraver with some part laying around and as you probably know, it is never finish and always need new upgrades. To make this short, I am trying to make ABL create...
View ArticleZ-offset question (1 reply)
Hi, Just added a BLTouch probe to my old Anet A8 (with Marlin 1.1.9) and looking at a number of YouTube videos about Marlin config and auto bed levelling. I have a significant...
View ArticleSKR 2, 2209's and a homing mess (2 replies)
I am using the sensor less homing set up. with the 2209's After upgrading to 2.1.2.1 I have a homing mess. After start up it will home 1 time from Pronterface, or 1 time from the TFT. After that if I...
View ArticleExternal drivers in marlin firmware 2.1.2.1 (1 reply)
Hello I use Marlin firmware 2.1.2.1. motherboard: Octopus pro V1.0 (F446) Bigtreetech. Printer: Cartesian - x-axis with ribbon - y-axis with ribbon, both with nema 23 closed stepper motor and both...
View ArticleFirmware advice. (1 reply)
Looking for some help understanding what I should be using for microstepping in the RepRapFirmware Configuration Tool. I have a skr 3 and I'm using tmc2209 drivers, so should I keep it at 16 for...
View Articleprobe offset value (no replies)
I have a 12mm inductive probe mounted on my Ender3. It is about 4.5mm to the left of the nozzle, 1.5mm in front of the nozzle, and about 2mm above the nozzle. (which would be in the negative X, and Y...
View ArticleMarlin 2 probing settings question (no replies)
I recently went form Marlin 1.1.8 to Marlin 2.1.2 for better stepper support and am now struggling with bed postioning and lineair probing. I'm now using the following settings in configuration.h:...
View ArticleFirmware settings retrieval (1 reply)
Is there a way to retrieve the firmware from the board on my 3d printe
View ArticleHow to save gcode to sd card using serial port (1 reply)
Hello I am looking for a way to save gcode on an SD card in a laser cutter using a python application on a Raspberry Pi connected to the cutting board via a USB cable. I made a port in python but the...
View ArticleBabystepping (no replies)
BABYSTEPPING_ALWAYS_AVAILABLE and MOVE_Z_WHEN_IDLE are incompatible. IE, you can't define both. BUT they seem to do different things. BABYSTEPPING_ALWAYS_AVAILABLE isn't really ALWAYS available. It is...
View ArticleEvolution to PRO for a Dagoma Ultimate V2 TMC (no replies)
Hello, I'm looking for help. I have a 3D Printer called Dagoma Ultimate V2 TMC It's based on Ramps and have 5 integrated TMC 2209 They call this board D6 (see D6 Board.png) [attachment 120609...
View ArticleCompilazione Marlin bloccata (3 replies)
Salve a tutti sono nuovo in questo forum e ho un problema con la compilazione del firmware marlin 2.1.2 su una scheda robin nano v1.2. Non ho trovato nulla in rete al riguardo e spero nella vostro...
View Article