Help adjusting ADC range values (1 reply)
Hi all, I'm Alex, 54, italian and I enjoyed 3d printing for 15 years now. I bought a mks tinybee to replace my defective anet a8 board, but the problem is not the board itself. I installed marlin...
View ArticleMarlin 2.1.2.1 M260 command (no replies)
Hello, I need the help with the M260 command M260 [A] [R] I am traying to send the data to the MCP4725 I2C device which adress is 0x61 which will be A97 Command I sent was M260 A97 B00 S1, response...
View ArticleMarlin 2.1.2.1 M260 command (no replies)
Hello, I need the help with the M260 command M260 [A] [R] I am traying to send the data to the MCP4725 I2C device which adress is 0x61 which will be A97 Command I sent was M260 A97 B00 S1, response...
View ArticleIs there a way to stop the current move but keep position? (5 replies)
or what does "freeze" do anyway? I'd like to be able to stop the current move mid-travel with deceleration and keeping motors powered, so that machine position is preserved. (I'm adapting an existing...
View ArticleMarlin Firmware support necessary (1 reply)
Hello together, i am facing a lot of different issues while configuring and compiling Marlin firmware for my 3D Printer. Few years ago (2018 / 2019) i bought a Creality CR10. Since i was unhappy with...
View ArticleCTC Bizer pin anomaly (no replies)
Hi, I must confess to be an owner of a mighty_board_rev_e for a CTC Bizer 2(ATMEGA 2560) Yes, I will move on I promise, its in the pipeline. I just need help with pin configuration. I have installed...
View ArticleMarlin 2.1.2.1 M105 Temperature serial response modification (2 replies)
Hello, On the Marlin 2.1.2.1, I am using 3 temperature loops, MAX31855 on the hotend 0, PT100 hotend 1, PT100 Bed. All heater safety and cold extrusion prevention are disabled. All work, ok. My...
View ArticleFilament Runout Sensor (2 replies)
Hello friends Tell me, when the girl connects the end of the filament , the print does not start, as if she believes that there is no filament . where is the inversion of sensor data configured? A...
View ArticleLength Filament replacement (no replies)
hello friends, tell me where in the configuration the length of the thread ejection changes, in replacement mode? then I have to repeat the operation 4 times when changing A Modern UI using LVGL
View ArticlePassive heating (no replies)
I have a BTT SKR 2 with a TFT35 E3 V3 screen The TFT firmware is set up like this; #### Heated Chamber Support # Enable/disable presence of heated chamber. # # NOTE: Disable it to let the TFT...
View Articlemanual bed leveling (no replies)
Hello, I compiled marlin 2.1.x and flash on my ender 3 v2 with manual bed leveling on marlin gui. I can do a manual level from lcd screen ui, and get the mesh values from command M420 V. If I send the...
View ArticleHotend0 PID loop output (no replies)
Hello, I am experimenting with the paste printing where material is not the solid and I need help modifing the hotend0 and hotend1 operations / temperatures.. I am planning to use Hotend0 to control...
View ArticlePCB Exposer Marlin Firmware:( (1 reply)
Hi, I have been working on some DIY PCB laser exposer project quite time ago.Then i saw that someone already done it which is Diyouware PCB.Here is original project page for it:[www.diyouware.com]...
View ArticleHoming to a Max Endstop (no replies)
Made a Custom Printer, MKS Gen L 2,0 board. Marlin 1.1.9 Using BL Touch. BL is on the LEFT side of the hotend housing. Can't home to X MIN (left side) because BL Touch. Moved bump stop to the right...
View ArticleBTT OCTOPUS more then 3 axis (3 replies)
Hi, I am trying to control more than 3 axes and I am having some problems with the code compilation. In the attachment, I put the config file what can I change? Thank you very much
View ArticleExtruder thermistor input TH1 - re-asighn ? (1 reply)
Hello, I need assistance in comprehending the thermistor0 that is connected to analog pin A13. I currently utilize the MAX31855 for the hotend0 and have successfully configure temperature loop for it....
View ArticleHelp configuration of the laser cooler loop (1 reply)
Hello, I require assistance in configuring the laser cooler loop for the Marlin 2.1.2.1 firmware and the MKS GEN L v1 board. I've made edits to the configuration files, but I seem to be missing...
View ArticleAquila X3 bed probe not working in Marlin/MRiscoCProUI (no replies)
Hello everyone I'm trying to change my Voxelab Aquila X3 firmware (because the default one as almost no options at all), but I’m unable to make the bed probe work (the X3 comes with an inductive...
View ArticleBTT OCTOPUS, TMC 2209 current status (no replies)
Hi, I know that the TMC 2209 has the StallGuard4 function that is used for the sensorless homing but there is a way of having feedback on the motor current in real-time with the usb serial ? i've...
View ArticleNeed help diagnose a strange ABL problem (no replies)
I suddenly have a strange behaviour with ABL correction with my printer. The printer is basically a Ender 5 Plus but with a MicroSwiss allmetal hotend, BTT SKR Mini E3 V3 and a CR Touch instead of the...
View Article