Not able to get the correct Z-position (no replies)
Using K8200 with a servo assisted Z-switch on Merlin 1.1.0 Bugfix (Also tried a capacitive sensor with the same result) When homing Z, it does it work, and then lifts up to 30. The real distance is...
View ArticleM107 G-Code (no replies)
Hi All I want the print cooling fan to stay on for a set amount of time after the print as finished. I know it's M107 ? followed by the time eather in seconds or milliseconds but I cannot for the life...
View ArticleFirmware Error - Help Required (no replies)
I am setting up a new printer and copied the firmware from an existing printer and run it through Arduino 1.6.8. Each time I verify I get the following error: I have totally no idea how to resolve...
View Articlemarlin 1.1.0 rc7 and inductor sensor 12vdc (4 replies)
hello , i just finished my 3d printer MPCNC version and since i have a large hot bed i need it a sensor to auto level the platform. well i can't figure out what i am doing wrong with Marlin firmware....
View ArticleHow is babystepping supposed to work with UBL? (1 reply)
I've, after significant effort and many tries, gotten UBL up and running. I'm confused, however, about two things. First, what am I supposed to put in the start g-code in my slicer? Previously it was...
View ArticleSD CARD PROBLEM - Marlin 1.1.0 RC8 (no replies)
Hi all, I've a problem with the sd card reader on my reprap discount lcd panel. I tried with a 2gb and a 4gb (FAT/FAT32 formatted) but I always get "no sd card" on lcd menù. In the info screen I can...
View ArticleEnable the Z steppers at startup (no replies)
I everyone! First of all I would like to thank the Marlin team for all the work they did on 1.1.0 version! I have a little issue that I hadn't before updating marlin. My bed is heavy and falls down...
View ArticleUsing relays for hotend and bed gives unexpected results (no replies)
Hi everyone! I have a RAMPS 1.4 board. Today I connected all the wires, including the ones for heated bed and extruder, providing double power supply to the RAMPS shield. I started a print, everything...
View ArticleMarlin firmware using universal g code sender ?Is it possible? (no replies)
I currently am running a highly modified version of marlin firmware with a megatronics v2.0 controller ..Wanting to switch over to using ugs platform as it has keyboard jogging features and other...
View ArticleClik here to view.
Marlin configurator (1 reply)
Introduce new version of Marlin configurator installation: sudo npm -g i marlin-conf then right click in Marlin folder with git repository and choose Open in Terminal and typemct updated version with...
View ArticlePositional feedback with rotary encoder: is it possible? (1 reply)
So, I stumbled on this part on aliexpress. You could attach a GT2 tooth there. The signal is transmitted via twisted pair interface, so quite immune to noise IMO. I am going to try develop a...
View Articlemini-rambo help (2 replies)
Hey guys So im kinda at my wits end with my problem. Started over the weekend I did a Bnechi print on my Lulzbot Mini. and ever since my machine will not make a good circle. They all come out shifted....
View Articleservo autobed levelling (no replies)
hello, i'm trying to use servo i configured everything like offsets from extruder, probing points, when i give G29 command servo extends and then probes to first point, and then it doesnt retract and...
View ArticleMovement bound question (no replies)
I have a GeeeTech MeCreator 2, and have moved settings to 1.1 (will contribute pin-file and configuration for the GT2560) I have one question, it is sold as a 160x160x160 printer. Old 1.0 firmware...
View ArticleLift Z on Tool Change (no replies)
Hey everybody! Is there such a feature in the Marlin firmware that allows you to lift the Z axis when you change extruder? I cannot seem to find it. Also another question is what kind of feature is...
View ArticleMarlin RC8 to Marlin 1.1.0 (no replies)
Hi, how do you upgrade to a new Marlin version? Is it necessary to compare the configuration files by hand or is there another way? Thx
View ArticleNeed a configuration.h File for Mendel90 ... (no replies)
Hello Friends, After a Year in Hospital I´m back into the Live ! I´ve decited to upgrade the Sorftware / Firmware on my Mendel90 (to the latest Marlin Software 1.1.1) But - I have a Problem with the...
View ArticleMarlin behavior and screen display (no replies)
Hello, I have recently upgraded my two anet a8 printers with skynet3d based on marlin 1.1. The upgrade was to use auto level. Auto level works on both printers and the firmware works as...
View ArticleMarlin Auto Bed Leveling Reverse Behavior (no replies)
Hi guys. I'm using Marlin RC7 and I enabled Auto Bed Leveling Grid option. I'm using a proximity sensor LJ12A3-4-ZBX and an MK3 Heated Bed. But the problem is that when the nozzle should go up it goes...
View ArticleError Z_MIN_ENDSTOP_INVERTING (no replies)
Hi, I'm updating RC8 to bugfix 1.1.0. I got a error while compiling that says: SanityCheck.h:521: error: #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match...
View Article