[SOLVED] how to implement second heater? (2 replies)
Hey there, I've got a FLsun Cube and got it with a single extruder but I want to implement a second extruder. The printer uses the MKS GEN_L V1.0 Board which actually has two heater ports but uses the...
View ArticleWhat settings in Marlin makes inductive sensor trigger correctly? (5 replies)
For the life of me I can't seem to figure out the Z-Min Endstop for a Inductive Sensor. I have LJ18A3-8-z/8X Inductive Sensor and it works. I have it wired right and the blue wire is in the Z-Min Pin...
View ArticleZ axis slams into bed/bltouch offset?/autohome, start print slams (2 replies)
Ok so i think its my bltouch offset it was 1.9 before frimware upgrade now it gose to 13.9 on z axis. But my printer offsets are 1.9 and dont go higher then 10? Also in frimware it thinks its at 1.9...
View ArticleNozzle touch auto bed leveling (2 replies)
I saw some printer on ali which use nozzle to touch heated bed in order to do autoleveling so I hew few questions How safe is this moving speed while touching bed is very slow ? Is this feature...
View ArticleClik here to view.
Bedlevelling (all types) is always slightly off. (no replies)
Hi, Just wondering if I could ask some advice on this : I am using a BLTouch, I have tried - UBL - Linear - Bilinear - 3 point - reverting to 1.1.4 and the results are always variations on a theme :...
View ArticleMarlin 1.1 Manual Bed Level Option on Mini Kossel (2 replies)
Hoping someone can assist, I am pulling my hair out with this one. Machine is a Sintron Mini Kossel. Endstops at the top. I am trying to configure the firmware for manual bed levelling from the LCD....
View ArticleTurn Hot-End Heater Output Into Always on Fan? (no replies)
Hello All, I was wondering if it's possible to reconfigure Marlin so that it uses one of my unused Hot-End Heater outputs as an Always on Fan output? It's but of a long story as to why I want to do...
View Articleend stops (1 reply)
I have upgrade my printer incl firmware ,latest Marlin 1.6,11 Now it's working except the endstops . I have electronic endstops type : opto endstop Before the update it did works . I don't know what...
View ArticleAuto switch-off? (2 replies)
Hi, I have my diy printer working and today I made my first 4-hour print. It all worked, I am happy. But on weekdays, making a 4 hour print would mean the printer sits idle for about 5 hours until I...
View ArticleAnyone know which board to choose for this? (4 replies)
[www.amazon.co.uk] more details here [www.aliexpress.com] Which option do I pick from boards.h?
View ArticleTMC2100 how to get into spreadcycle? (no replies)
Ok so it seems every driver clone seems to be wired differently. Anyone know how to get this into spreadcycle? [www.aliexpress.com]
View ArticleRAMP board steppers one direction only? (no replies)
I posted this under RAMPS hardware, but realized maybe it is a software problem. I have Marlin loaded on my RAMPS board and Arduino. Move axis can only step in the + direction (XYZ) There is a...
View ArticleHictop 3DP11/12 Controller (no replies)
I Have a Hictop Controller connector diagram below for the MKS.3 controller. Digital output Analog input ┌───┬───┬───┬───┐ │ D12 │ D11│A12 │ A11 │ ├───┼───┼───┼───┤ │GND│GND│GND│GND│ ├───┼───┼───┼───┤...
View ArticleX axis too fast when starting print. (no replies)
Hi Guys, Setting up a MKS gen v1.4 on CTC biezer. Using Marlin 2016 Firmware. I've just about got everything working. controlling via TFT32. bed manual leveling works correctly, along with 'home'...
View ArticleNo voltage to the bed with Rambo (4 replies)
Hi all, first time poster long time lurker... So I'm building a machine using a mini Rambo and am running into a problem I really don't understand. When I send the Gcode to turn on the nozzle heater,...
View ArticleNeed help setting probe points for UBL (no replies)
I have a 300 x 300 bed, my probe has offsets of X -29 Y -51 I need around 10mm clearance around the edges of the bed to avoid my binder clips. Due to the position of the probe, I can reach the front...
View ArticleConfused about UBL (no replies)
Hi, I have read the excellent documentation on UBL and created mesh, done a test print and everything looks perfect! My mesh is now loaded but this is where I get confused. Should UBL do a test probe...
View ArticleMotors Speed painfully slow (no replies)
Gentemen, I´ve recently built my first 3D Cartesian printer. I am using NEMA23 steppers connected to 3mm pitch lead screws, driven by pololu drivers, RAMPS1.4 board and Marlin fw V1.1.5. Honestly,...
View ArticlePrint gaps. Marlin settings, slicer settings or mechanical? (3 replies)
I have now upgraded my A-101 to an E3D-V6 hot end. Now I'm back to figuring out the problems that I set out to figure out before I buggered the old nozzle... The photo below is of the right most...
View ArticleCompiling Marlin on a raspberry pi 3 (3 replies)
i uploaded Arduino IDE onto my PI3 and when i try to compile Marlin it has multiple errors. I copied my working copy of Marlin from my PC directly to my pi including all the subdirectories and...
View Article