dual extruder upgrade problem (no replies)
I have upgraded my Hictop 3DP08 to dual extruder. It now has 2 extruder stepper motors and XCSOURSE dual J head nozzle extruder kit which has 2 nozzles, 2 thermistors and 2 heaters. I have configured...
View ArticleHow can i move a menue item to another position? (no replies)
Can anyone please explain me how can i change the ultralcd.cpp to move the menu item Main -> Prepare -> Preheat PLA "Preheat PLA" one level up or to the main menu ? many thanks!
View ArticleTravelING_FADE_HEIGHT availalbel in Marlin 1.1.x? (no replies)
Hi at all, is there any possibility in the Marlin FW to lift the nozzel, during a print while traveling from one point to another one. So the nozzel don't hit any of the all ready printed object, when...
View ArticleExtruder 2 not working (no replies)
I have upgraded my Hictop 3DP8 printer to dual extrusion, using the XCSOURCE dual J head nozzle extruder, so it now has 2 nozzles, 2 thermistors and 2 hot ends. I can not get the 2nd hot end to heat...
View ArticleMirrored text fix, I missed something? (no replies)
Hello, I recently rebuilt my printer, it was a GeeeTech ME Creator (original version) I basically tore it apart and started over, Bowden J-Head, Ramps 1.4 with TMC2100 lead screw etc etc etc Got rid...
View Article1.1.5 getting mesh bed leveling working (no replies)
I just rebuilt my printer and setup Marlin 1.1.5 from scratch. I enabled #define MESH_BED_LEVELING and now I see the bed leveling option in my LCD panel menus. BUT!!! All it does is home all axis.......
View Articlehow g33 works? (no replies)
My probe I installed is far away from the nozzle (offset -x45 y17), maybe my endstop z or hotbed is not level, the result is useless. My question is how to level the endstops? is G33 my solution? if...
View ArticleMarlin 1.1.5 (1 reply)
I have a unique problem It involves "Endstop Trigger reporting" I get an error Using a Proximity sensor TL_M3W 'NPN' NC as a Z-Axis endstop. using these lines of code. #define...
View ArticleClik here to view.
Inductive Z-probe not seen by Marlin / RAMPS 1.4 (1 reply)
Hi, I just replaced my microswitch Z-min switch (which was just on there for testing and it works) with a "SN04-N 4mm Inductive Proximity Sensor Detection Switch NPN NO DC 10-30V" from ebay. I wired...
View ArticleCompiler Error (1 reply)
Hi guys, I am a new boy on the block..... I am building my own 3d printer - have not got it built yet, but i thought i would progress on the electronic side simultaneously, then once i get some...
View ArticleAnycubic kossel Stuttering (no replies)
Hi Everyone. Dident know where to post this but as i maybe think its firmware specific i try here. If not then maybe admin can move it to a more appropriate section of the forum ? Ive build a...
View ArticleQuestion on G29 output (no replies)
I am running Marlin 1.1 and have turned on MESH_BED_LEVELING since I don't currently have a working probe. I'm using the default 3x3 mesh grid. After I perform the manual bed leveling (G29 S1, G29 S2,...
View ArticleHelp Frimware Delta mini (no replies)
I have a Delta printer but I have a case Slow down the delta speed too slow how can i set up the marlin firmware?
View ArticleIssue uploading Marling Firmware on RAMBo (no replies)
Guys I need some help here. For a long time I have used RAMPS on my Prusa I3 but I decided to make some upgrades, then I bought a RAMBo and installed it on my printer. The point is that I can't upload...
View ArticleBed leveling data saved? (6 replies)
Hi, I've been using Marlin for a couple of weeks in my DIY Prusa clone and my first layer has been very hit and miss and I might have found out why! On the Marlin Wiki it says that the bed leveling...
View ArticleHelp Marlin (no replies)
Please help me with this error Arduino: 1.8.3 (Windows 8.1), Bo mạch:"Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from sketch\MarlinConfig.h:39:0, from...
View ArticleCreality Ender-4 GPL violation? (no replies)
I just got a Creality Ender-4; its ultimately a pretty solid printer- though it does suffer from low production values (my heater cooling fan broke within 14 hours and I had no way to interact with...
View ArticleMarlin 1.1.4 - Parameter S, T and B of M205 (1 reply)
Does anyone know the function of parameters S, T and B of command M205?
View ArticleRambo v1.0e (no replies)
Anybody know if the latest version of marlin will work with a Rambo v1.0e board?
View ArticleG33 - lcd_probe_pt error message (no replies)
I'm trying to figure out G33 Delta Auto Calibration on my Anycubic Kossel Plus. No probe so I was planning on doing the paper method with G33. Using a fresh copy of the latest Marlin FW 1.1.5 #9c00cff...
View Article