Printer will not heat beyond 260C (2 replies)
Hey guys, I recently upgraded to an e3d v6 and bumped up the temperature limit to 295C. Whenever I try to heat beyond 260C it shows printer halted, heating failed. Even though I managed to PID...
View ArticleStandard fan PWM frequency (no replies)
Hello everyone, I have been looking on google for a while, what PWM frequency does the part fan run at? But I cant find answer. I am designing a closed loop speed control circuit, The circuit needs a...
View ArticleLimit Switches not Working (Pin Config) on 5D Print D8(Makibox) (1 reply)
Hello Everybody, I have a Problem with my Makibox(newer Model with a 5D Print D8 board): After having some Problems with the original Firmware on the Board, i decided to re-program it with Marlin....
View ArticleM280 GCode out of order (no replies)
Hi, I'm currently building a pen plotter using Marlin firmware v1.1.3. I'm using RC servo to lift the pen instead of stepper, so my Z axis control is M280 P0 Sxx instead of G1 Zxx When I try to draw...
View ArticleSync_plan_position_e() dual extruder bug (no replies)
Hi, i have a dual extruder printer with marlin firmware. The problem is when i use the 2th extruder.After call change tool gcode (T1) and call the gcode "G92 E0" the printer lose position and go...
View ArticleUsing Marlin with a MakerBot Rep2 (no replies)
Hello, everyone! My club has a bunch of MakerBot Replicator 2s that have started to break down. We've been trying to figure out how to convert them to open source electronics, software, and an E3D...
View ArticleClik here to view.
Marlin and Full Graphics Smart Controller (2 replies)
Hello guys, i've installed a RepRap Full Graphics Smart Controller on my i3 Hephestos but im having a bit of an issue with it. Everything works but the screen (after a few minutes, sometimes seconds...
View ArticleBLTouch & Delta Issue (no replies)
I'm just building an Anycubic Kossel plus and have added a BLTouch Smart probe. I'm running on a very late snapshot of bugfix-1.1.x. I've got got an issue in that when doing an delta auto calibration...
View ArticleDisplay the Measurement Result during Bed Leveling (no replies)
Is it possible do display the measurement result of each point during bed leveling on the LCD screen? Watching these values during bed leveling would give a good information about the alignment of the...
View ArticleStuck on STOPPED (no replies)
I am running Marlin 1.1.2 on a Tevo Tarantula with BLTouch. I mistakenly unplugged the AC to the power supply while it was running a print job. Now I cannot home the Z axis. The LCD display shows...
View ArticleUnderstanding my flavor of Marlin (no replies)
I have downloaded a copy of the Marlin firmware version currently installed in my printer (Lulzbot TAZ 6) mostly for my own education. I can look at the source code but because of the heavy dependency...
View ArticleCan't compile Marlin (no replies)
Hi, I try to compile Marlin for my Anet A8 and get an error. What do I do wrong?
View ArticleRRD 2004 Configuration (no replies)
Hi I recently acquired a RAMPS 1.4 board including a RepRapDiscount Smart Controller for Arduino Mega 2560 with a 20x04 LCD screen, and have installed Marlin 1.1.4 I'm having a slight configuration...
View ArticleTwo Y_min stops and homing the extruder (no replies)
Hi guys, currently I'm working on a project that involves two Y motors. It's basically a gantry like this: [youtu.be]. But with two Y motors instead of the coupler + linear rod setup. I made the...
View ArticleExtrusion Issues when updating to Marlin 1.1 (no replies)
I have an “old” printer (Bukobot circa 2014) which has an Azteeg X3 board running Marlin from about that same period. I don’t have the code that the board was installed with, but I do have the...
View ArticleMarlin 1.1.4 (no replies)
Now I have two Hictops one 12volt and One 24volt. They have the same controller card they were both upgraded to Marlin 1.1.4-RC6 - they both have different problems. The only firmware lines that are...
View ArticleM218 Z-Offset without DualCarriage or SwitchingExtruder (no replies)
Hello! My multi-extruder printer can switch complete toolheads automaticly. They are clipped on with magnets and can be interchanged by moving to a certain position. That way, the height of the...
View ArticlePrinter slight pause during prints (no replies)
Hi Guys While my print is printing the printer will do a slight ( 2 second ) pause and carry printing. It seems to happen when it move to other parts of the print. I have changed & bought a new...
View ArticleMarlin 1.1.4 UBL issue (no replies)
Hello, im trying to configure UBL on my Sunhokey I3 with capacitive probe connected to z- min endstop G28 works as expected. I have 3X3 mesh set in FW. I'm following [marlinfw.org] for setup. The...
View ArticleSilicon Bed Heater Temperature Problems with Marlin 1.1 (2 replies)
I bought a new silicon bed heater and aluminum bed does not appear to be getting accurate temperature readings. The product docs clearly states that the thermistor is a "NTC 3950 Thermistor built in...
View Article