Need help configuring extruder_fan & part_cooling_fan (no replies)
Hello, I am trying to configure marlin 1.1.8 working with my printer, but I am having problem working the extruder_fan and the part_cooling_fan. Can anyone please help? About the extruder_fan. I have...
View ArticleDual X Carriage not working (no replies)
last month i build my dual x-carriage printer with Rumba board i try to modify marlin bugfix-1.1.x, but it has some problem 1. x2 carriage look like move to left when homing 2. x2 filament cooling fan...
View ArticleExtruder stutters and doesn't turn (no replies)
Hi guys, I've replaced my printers board with a RAMP 1.4 and Marlin 1.1.8. I've put the TMC2130 drivers on, on all axis (including extruder). Everything seem to be working, except my extruder. When I...
View Article1.1.x_bugfix Leveling issues (2 replies)
Hi- I am having trouble with bilinear bed leveling with the 1.1.x bugfix release. I can not determine if its the sensor being flakey or if its the firmware. Here is a video of Autohoming and G29...
View ArticleConnecting 2 E mottors (no replies)
Hello! I have CTC dual with MIghtyboard electronics and changed firmware to Marlin (attached to post). I would like to control both E motors simultaneously, as one motor. I tried to use mixing...
View ArticleInvert Logic of any Digital Pin used for Fans and Lights (no replies)
Hi Folks, I did some smaller mistake in my Hardware "design" as I soldered a small Board to switch Fans and Lights With D47 D45 D43 and D41 The Board Works as expected but Digital HIGH turns the light...
View ArticleBLTocuch 3D on Marlin 1.1.8 and other issues (no replies)
Hi everybody I built my own 3d printer and I am using marlin 1.1.8 firmware. I cannot put BL Touch 3D working, as well as endstops. Also I got error when triyng to warmup bed to 110º to print with...
View ArticleClik here to view.
How to remove marlin logo on reprap discount lcd (2 replies)
Hi guys can anyone please tell me how can i remove or change the marlin logo on splash screen / boot screen on reprap discount lcd. ibb.co how to delete twitter account permanently
View ArticleTEMP SENSOR CHAMBER (1 reply)
While running through a configuration.h file the other day on this 3D forum, spotted the following line of code. #define TEMP_SENSOR_CHAMBER 0 It however it had no other supporting information with...
View ArticleConfiguring 3DTouch bed leveller: Tevo Tarantula (4 replies)
Let me start by saying I'm a not very technical newbie. I have a Tarantula which I finally managed to update Jim Brown's Tevo Tarantula easy config from GitHub. Even that was a struggle with my level...
View ArticleConfiguring add.serial port on Ruma +, need help...:S (1 reply)
Hello all, Working on a custom project that will use a 7"tft/Mega combo as a touch screen for my reprap with a Rumba+. The interface between the two systems will (hopefully) be via serial comms. By...
View ArticleCan't figure out BLTouch offset (no replies)
I cannot figure out how to get the leveling values produced by the BLTouch to register. I'm using a custom 3D printer and Marlin bugfix 2.0.x. This is what happens: G28 to home printer G29 and the...
View ArticleDIGIPOT_MOTOR_CURRENT Compiling error (1 reply)
Hi I am trying to compile my marlin code so I can upload it to my printer and I keep getting an error. The error I am getting is that it says that the 'DIGIPOT_MOTOR_CURRENT' was not declared in this...
View ArticlePrint job does not start (1 reply)
Hi everybody When I start a printing job the printer after heating goes to a point and wait for the filament to be exchanged and it stays at "Print paused". After filament is chaged and extruded I do...
View ArticleDiamond Hotend M163 - Set Mix Factor (no replies)
Does anyone knows how to convert a CMY color to the mix factor ? Example (Caucasian Skin color) C = 6 M = 27 Y = 32 K = 0 RGB equivalent: R=240, G=186, B=173 How to convert these values to a mix...
View ArticleMalyan M150 - latestr firmware (no replies)
Hi Guys I have Malyan M150 with stock firmware. So far I was happy with that but I've bought autolevel sensor and for this feature I need new fw. Could you please answer my questions? can I download...
View ArticleG29 Z Leveling not going in the right direction (no replies)
Hi there, Hardware: Tronxy P802EA with MKS Gen 1.4 board Firmware: Marin (1.1.x.zip … 1.1.8) I'm trying to work out what is wrong with the auto levelling feature G29. All of XYZ axis are moving in the...
View ArticleMarlin 1.1.4 with two end stops possible? (no replies)
Hello All I have a Tarantula printer and want to use besides the standard Z end stop an additional sensor (captive NPN type LJC12A3-4-Z / BX for glass). Is it possible to leave the end stop switch in...
View ArticleG29 - Autoleveling for Tool Changing (no replies)
Hello, I'm using Marlin on a custom FDM printer running on an MKS 1.4 board, slicing with Simplify 3d. The printer has 3 different heads, so I can change between materials/nozzle sizes. The tools have...
View ArticleG92 Problem (no replies)
Hi, I have just rebuilt the hardware on my MakerFarm 12" Prusa, at the same time I upgraded Marlin from 1.1.3 to 1.1.8. I transferred the changes I had made in the old Configuration.h file to the new...
View Article