M0 - Stop that doesn't turn off heaters and motors (no replies)
In Cura there is a post-processing script, Pause at Height, that will insert gcode to pause the printer and wait for the user to continue and the current implementation uses M0. According to the...
View ArticleCheap Chinese TB6600 with Marlin (2 replies)
Hey Reprap community, So, I've bought these cheap chinese TB6600. They have a Toshiba Stepper driver chip S109AFTG. It's actually a pretty good chip. Not fully implemented in the design, but it will...
View ArticleMarlin menu item selection (1 reply)
In Marlin 1.1.8 selected menu item is marked only by 2 thin lines above and below, at least on my Anet A6. Anyone know if there is some sort of editable setting to make the selected menu item appear...
View ArticleBLTouch Matrix and Return to X/Y Home (no replies)
Hello all! First post and very new to 3d printing/coding. So, please bear with me, and if you ask me for detailed information (error reports, etc..), I will likely need some coaching. But I will do my...
View Articleextruder fan is not affected by FAST_PWM_FAN (no replies)
In the latest version of marlin (1.1.8), I set the E0_AUTO_FAN_PIN to 44 and FAN_PIN to 9. I tried to reduce the fan speed for the extruder by setting EXTRUDER_AUTO_FAN_SPEED, but the PWM caused some...
View ArticleHow to start levelling from scratch? (2 replies)
I have quite unsuccessfully tried to implement auto bed levelling on my Cartesian printer many times. I suspect that I now have my Marlin 1.1.8 FW pretty messed up. My main issues are with...
View ArticleMarlin 1.1.8 Heating failed error (no replies)
I have ben converting my duplicator i3 to an MKS GEN 1.4 running Marlin 1.1.8 and every so often I get Errors about heating. Tonight I tried doing the PID autotuned for the heatbed. I used Repetier...
View ArticleChange preloaded Firmware Bed dimensions? (no replies)
Bought an OVM20lite a couple months ago. cute, cheap, single board ramps spinoff, that, as i just discovered, doesnt seem to be continued. downside: CH340 driver. came preloaded with Marlin 1.1.1,...
View ArticleAcceleration settings (no replies)
Hi guys, So, checking the acceleration menu (Control>Motion>Acceleration) i can see several acceleration settings. Acceleration A-retract A-travel Amax X Amax Y Amax Z Amax E What is the...
View ArticleSD Card problem on STM32F103C [bugfix-2.0.x] (no replies)
Hi, I have compiled Marlin 2.0.x for STM32F103CB and Malyan M200 board but uploaded to a "Blue Pill" board using PIO. Since it's basically the same chip I expect most features to work. Serial...
View ArticleChanging Flow Rate or Filament Diameter Doesn't Change Anything (4 replies)
Hi all, Marlin currently is driving me crazy. Starting with the update to 1.1.7 my flowrate was by far to high. I had to set filament diameter to 2.5 to print properly using 1.75mm filament. Currently...
View ArticleWhat's the version used for my machine? Should I upgrade? (2 replies)
I have a RepRepGuru Prusa i3 V2, and they provide a download of Marlin firmware on their site. Can I look at the code and determine what version they used? Which file is it in? It has a copyright date...
View ArticleFilament out after first layer (3 replies)
Hi everybody I'm having a problem with Marlin 1.1.9. I start printing and everything goes ok, but after the first layer extruder goes to the back of the printer and takes out all the filament and then...
View ArticleManual bed leveling (1 reply)
Is there a setting in Marlin that I can define which will allow me to make a moves to each of the 4 corners and level the bed manually with the screws?
View ArticleDo the adjustments from UBL get applied only during a print? Or do they apply...
I'm about to move to 1.1.8 from 1.1.4 and I'm going to give UBL a shot but I'm curious: do the mesh adjustments apply during normal moves, or only during prints? For example - what if based on my mesh...
View ArticleDual X carraige X2 stepper pin define (no replies)
I have just modified my P3Steel, Toolson edition, to a dual X carraige with two E3d hotends. Using my old 1.0.1 firmware, I was able to configure the X2 stepper pins in Configuration_adv.h and...
View ArticleMarlin on Zonestar P802QR2 (no replies)
I currently have Marlin 1.1.7 on my dual extruder QR2 and it's working "kind of". I can't seem to correctly align my nozzles though. So on lines 215 and 216 of Configuration.h line 215 seemed to have...
View ArticleBLTouch setup FT5 (no replies)
Folgertech FT5 Mks Gen v1.4 Marlin 10-7 Bugfix Repitier-Host bed X 295, Y 295 BLTouch classic mounted 54mm to left of nozzle (0,0 on FT5 is at right rear) Only probe offset is the Y 54mm X, Y, Z...
View ArticleServo control from MKS base 1.4 (no replies)
So I'm trying to control a servo motor from the board. But I cannot figure out for the life of me how to edit the code. If I don't enable "servo probe", then whenever I send M280 command it just says...
View ArticleMarlin M4/M5 Laser commands functional? (no replies)
Morning all, Just bought a laser to add to my JGAurora A5. I've been looking through the firmware and from reading I need to change the Fan D9 to D44, but I then noticed this was already assigned now...
View Article