X, Y not moving. (2 replies)
I am in the process of building a CoreXY machine, and have the mechanical parts (including the stepper motors) of the X, Y and Z axes installed. I wanted to stop at this point and try moving the X and...
View ArticleZ axis switch not working (1 reply)
After uploading marlin 1.1.8 to my I3 printer and autobed levelling was already enabled Z axis switch doesn't work. I tested with M119 code and it say z_min: open when I press z switch it say z_min...
View ArticleAuto Calibration G33, std deviation (no replies)
What std. deviation mean ? I did use G33 and got a std. deviation of: 0.008 on my Delta with 220mm bed diameter. The leveling grid data from this printer: Bilinear Leveling Grid: 0 1 2 3 4 5 6 7 8 0...
View ArticleAnalog vs Digital PIN assignment (no replies)
Hello, How are the pins declared analog or digital? To keep things short and simple I will say what I am doing, and that it is working. My problem is I do not understand how it is working. Basically I...
View ArticleHow do I save bed leveling mesh data to SD card or Host (1 reply)
Hello all, I have a Delta. Running marlin bugfix 1.1.x (2 weeks old). I update the firmware every few weeks or so. The only thing that is a pain is redoing the unified bed leveling fine tuning - G26....
View ArticleWork screen (no replies)
Hallo all, I have a bad eye-sight and i want to restore the LCD selection to the way it was in older versions of Marlin. In the current version of Marlin it shows two bars: one above and one below the...
View ArticleVolumetric Extrusion settings (2 replies)
I want to start playing with the volumetric extrusion capabilities of Marlin, but it's a little unclear to me after reading what little bit of info is out there exactly how to set it up. Triffid...
View ArticleBoard loosing connection when PSU is switched on (no replies)
I have a MKS SBASE 1.3 that I am trying to set up. I have successfully managed to put Marlin on it using PlatformIO via Virtual Code Studio. However, I was trying to test the board by connecting a PSU...
View ArticleExtruder retracts before start of print (no replies)
Hi All, My extruder seems to retract about 3-4 mm just before starting to print, this menas that it will only print half of my "purge line" Could you please tell me what's wrong? This is my "start"...
View ArticlePositioning Extruders after Tool change : Marlin 1.1.6 (no replies)
I'm currently working on a project which uses two extruders. One for making an impression in a powder and other one to dispose a liquid in to the impression made by the first extruder. I'm currently...
View ArticleSN-04 sensor inconsistent (no replies)
I am running an SN-04 sensor on an Ender 3 powered by a Re-Arm. Board and sensor voltage is 24 Volts and version is Marlin 2.0.C bug fix. I am getting inconsistent readings, even though I used 2...
View ArticleRetraction speed question (no replies)
I've determined that my max speed for extrusion of my current roll of ABS is 5.3 mm/s @245C. I determined that by marking the filament and running 50 mm, increasing the speed until the extruder...
View ArticleClik here to view.
Can't set Z probe offset (1 reply)
I have a Delta printer. I've just upgraded it with Hiwin and new carbon rods. I can't set the proper nozzle height and so the printer goes too close to the bed and don't extrude. I have a nozzle based...
View ArticleG code for changing linear advance settings mid print? (no replies)
Hi, I would like to know if it is possible to change the linear advance value mid print when I change to another filament, and if so what the resulting g code would look like.
View ArticleTMC2130 not functioning - Ramps 1.6 (no replies)
Hello, I'm using the TMC2130 with senseless homing combined with a Ramps 1.6 on Marlin 1.1.x Bugfix. I installed an SD-Cardreader and an LCD so I had to reconfigured some pins. (based on this...
View ArticleXY Homing Offsets (no replies)
Hi There, The XY endstops on my i3 type printer is 10 to 12mm outside the printing area. It is fine for X and Y homing but not for the Z Probe which does not sense the buildplate. Is it possible, for...
View ArticleIndependent motor speeds for all axis (no replies)
Hello, TL;DR: Is it possible (that is, within reason and not having to rewrite half the code) to make each motor turn at an independent speed from the others? I am aware that the objective of the...
View ArticleA8M Anet printer (no replies)
I have a problem with Marlin flashing my mother board when I try to verify Marlin I get a error message. #endif / / BED_LEVELING. What did I miss?It said #endif without #if ? [attachment 106311...
View ArticleClik here to view.
Mesh Bed Leveling - add points. (2 replies)
I have a cr-10s and would like to add 4 more points to my mesh bed leveling pattern. However, I do not want to add them to the outside line but rather in select midpoints between the outer edge and...
View ArticleBLTouch self-start enable after Zmoves down by 10mm (1 reply)
Hi, I am using BLTouch. I am using MKS Gen V 1.4 + TFT3.2". This TFT is having 'Print resume after power outage'. So, whenever the power comes, the print can be resumed. Now I have added BLtouch to...
View Article