#define ABL_UBL error (no replies)
hi there when trying to enable #define ABL_UBL i get a compile error Arduino: 1.8.9 (Mac OS X), Board: "Arduino Mega ADK" sketch/Creality_DWIN.cpp: In member function 'void RTSSHOW::RTS_Init()':...
View ArticleY Axis not moving fast. (no replies)
Good day All! Into: I am using RAMBo v1.3 with Marlin FW 1.1.9 on my 3D printer. Configuration : My 3D printer is made out of aluminum extrusion and has a large print bed. Travel limit for X is 500...
View ArticleCNC/Laser Enable (2 replies)
Hi All it has been a while. I am building a 4W blue laser engraver I was using a Arduino Uno/CNC shield with GRBL firmware Worked ok but was not fast enough max power on Laser was 1 W any higher would...
View ArticleFAN0 inverted PWM? (3 replies)
Hey guys, my Anycubic I3 Mega is acting a bit weird. A M106 S0 or M107 spins the fan up to 100% whereas M106 S255 makes it run at about 10%. There seems to be some kind of inverted PWM signal. It also...
View Articleneed help to use 2.4" TFT LCD with marlin v2.0 (no replies)
Hi every one. I have a 2.4" TFT LCD Shield for arduino Uno and Mega2560. It uses ILI9341 driver . i searched the marlin pin assignment for RAMPS bud coulden't find any pin assignment for this type of...
View ArticleWhat EEPROM ranges does stock marlin use? (2 replies)
Hello! I am making a custom firmware for better control of running a laser on the 3d printer. I have some values I want to store in the EEPROM, but do not know what ranges are used by stock marlin....
View Articlebabystepping (no replies)
I tried to setup baby stepping on Marlin 1.1x and getting an error SENDING:M290 Z0.05 echo:Unknown command: "M290 Z0.05" SENDING:M290 Z-0.05 echo:Unknown command: "M290 Z-0.05" ' Has marlin dropped...
View ArticleMarlin2 M701/M702 compiler error (1 reply)
Hello fellow printers, I tried to enable the M701 and M702 gcodes today in config_adv but I get a compiler error that I cannot make sense of. I hope this makes more sense to one of you :) Please find...
View ArticleRead Enstop Hit-State Before Homing (no replies)
Hi RepRap community, first of all a big THANK YOU for all the information this forum provided for my little projects over the last years. This is my first question as an member of the RepRap Forum and...
View ArticleA certified (CE, UL, FCC...) PCB that can run Marlin (1 reply)
Hi, Seems that the issue of certifying boards is not so much in the minds of printer makers and PCB makers... :) Maybe someone here knows if there is any Arduino Mega 2560 board that is certified and...
View ArticleMarlin Menue request (no replies)
I know I can set up Marlin to use M600 to enable me to change filament and that there is an option in the 'Tune' menu but that is only available during a print. An option in the 'Prepare' menus to...
View ArticleMerlin Guru - your help is required please? (no replies)
I have just completed building my R3 Lite CNC which has turned out to be a really interesting build and, more to the point, a good strong and rigid small CNC (with approx. 12" x12" work area) and is...
View ArticleMarlin - setting up aNema 17 with planetary gearbox reduction (no replies)
Hi guys, I would like to ask for some ideas, because I've exhausted mines abut this. For the Z axis I was using a stepper motor attached to some guide rails and was managed to get it working fine, but...
View ArticleTMC2208 in UART mode on the SKR v1.3 (no replies)
I'm trying to get the SKR v.13 controller up and running with the TMC2208 stepper drivers. There are plenty of tutorials online on how to do this so it looks pretty easy. However, I cannot get...
View ArticleHead does not move in x and y when trying to build UBL mesh (probes in same...
Hi all, Does anyone know why the head doesn't move in x or y when attempting to build a UBL cold mesh? FWIW I'm doing this from the LCD menu. This is on a Bigtreetech skr1.3 and the Marlin 2.0 bugfix...
View ArticleSimulating printer head trajectory (2 replies)
Hi All, I have a lulzbot Taz 6, which runs on merlin firmware. I'm working on a project where I want to track what happens during a 3D print, and compare that to gcode. Specifically, I put rotary...
View ArticleX_SERIAL_(RX|TX)_PIN information not recognized - compiler error (no replies)
Hello everybody, I am trying to run my TMC2208s on my Anycubic i3 Mega in UART mode. All necessary hardware changes have been made and now I am running into an issue when I am trying to compile...
View ArticleEnd stops, steppers and display question (no replies)
Hi all With M17/M18 one can enable and disable steppers The M18 allows to selectively enable steppers- is this also possible to enable selectively- i.e. only X, Y or so? Same for end stops M121/M122,...
View Article[Help] Print stops mid-print (Marlin) (no replies)
Hi, I'm experiencing a very weird issue I'm unable to debug. I have a relatively small print I'm trying to print to test if the alignment of the nozzles on my dual extruder is correct, and whenever I...
View Article