I can't find the pioenvs folder in the last Marlin 2.0 bugfix (1 reply)
I can't find the pioenvs folder when I compile in Marlin 2.0 bugfix downloaded today , the whole process is correct, but when I look for the folder to use the .bin file the pioenvs folder doesn't exist.
View ArticleMarlin 1.9 Printer Halted when G28 (1 reply)
I was upgrading my MK2 Clone to use TMC2130 on all drivers X, Y, Z and E0. Got a virgin marlin 1.9 copy and set it up to the point I was kinda secure about it. Trying to set up SPI mode, stealthchop...
View ArticleMarlin G-force9-AC, Arduino 1.8.9 (no replies)
I have posted this in the Delta Printer section under FLSun, slow response there and I realized it might be more appropriate if I stated my situation here. I am using a Mac Mini as my control computer...
View ArticleTMC2130 Layer Shifting Above ~30mm/s (no replies)
Hi everyone! I have recently made the decision to gut the motherboard out of my Da Vinci 1.0 Pro because of malfunctions and the extreme noise. I replaced it with an SKR 1.3 and TMC2130's on XYE axes...
View ArticleFlashing latest version of Marlin (no replies)
I have converted a Reprap Prusa I3 to a core XY printer. Everything is set up apart from the flashing of the Arduino/Ramps board. I have an older version version of Marlin installed on there. Can I...
View ArticleHeating issues (3 replies)
Hello all, so I have recently upgraded my printer from a direct drive single nozzle printer to a dual nozzle bowden setup. I am currently trying to work out the issues that I have, so far I have been...
View ArticleClik here to view.
Marlin 2.0 relative extrude on external signal (1 reply)
Hi, I have a MKS gen1.3 board with Marlin 2.0 on it, as the title, I want the extruder motor to start extruding when an external signal is on. I only have 1 exturder, so i'm thinking of using the pins...
View ArticleEnd stop triggered, want to continue in oppo direction (no replies)
Hi all Have project plotter, `marlin, Ramps, `mega 2560 When a end stop is hit, the “print” stops, I want it to continue in the opposite direction- how can `i get there? Abort on end stop is disabled,...
View ArticleHowto turn on UNICODE filenames?? (no replies)
I run marlin 12.xx on arduino and mks sbase I use cyrillic settings for menus ( I use rrd smart discount LCD ) All works perfectly but I used to cyrillic filenames on smoothieware but my attempts to...
View ArticleMarlin 2.0 BugFix on ReArm controller (3 replies)
I Have successfully compiled Marlin 2.0 BugFix to the MicroSD on the ReArm controller using Platform IO ( interestingly not real easy) although I now have a Firmware.cur file and the ReArm board...
View ArticleUnable to compile Marlin 2.0.X if I enable EEPROM (no replies)
Hello everyone, I'm pretty new to 3D printing and compiling the firmware. A few weeks ago I added a SKR1.1 board to my printer and for the most part, had a perfectly functional 3D printer until I...
View ArticleG33 randomly fails (no replies)
I have delta and recently upgraded to a 32bit board (SKR 1.3) and also to TMC2130 (and I have 256 micro-stepping). No matter what, when I run my usual printer calibration routine (G33 P1, P2, P5, P10)...
View Articleset nozzle position after homing (no replies)
Printer: Anet A8 with Marlin 1.1.9. After I do an "auto home" command from the LCD menu The nozzle comes to rest at about 50 mm in front of the bed center ( i.e. 110,60). Is there a way to set the...
View Articlewrong Z-pos value after G28 home (no replies)
Printer: Delta / Kossel Mini (slightly modified) I just upgraded my firmware today from 1.1.0-RC6 to 1.1.9 My nozzle is 212.5 mm above heatbed and thats what the old firmware properly reported, based...
View ArticleError on arduino core ccp (4 replies)
I am currently working on re flashing the software on my geeetech I3 pro b. While compiling the marlin for loading I get the following error codes - core.a(main.cpp.o): In function `main':...
View ArticleInductive Z-Probe "triggered" when near metal, but will not stop (no replies)
Hello, I am trying to upgrade my SKR 1.3 Board to be used with an inductive Z-probe that I used to have on an earlier build. When I enter "M119" I accurately receive either "READ: z_min: TRIGGERED" or...
View ArticleHow / where to enable UI encoder (no replies)
I am trying to configure Marlin for a Ramps 1.6 board on a MEGA 2560 . I have an I2C 4x20 character LCD enabled. I have the LCD working with #define LCD_SAINSMART_I2C_2004 I have a separate encoder,...
View ArticleWeird behaviour : z probe offset bed levelling (no replies)
Hi, I tried everything to solve my problem and I can't find an answer anywhere so I am giving it a shot here. Sorry if it has already been answered. Everytime I do an automatic be levelling (any type)...
View ArticleBoard definition for Creality 1.1.5 board (no replies)
Hello, I am wanting to flash Marlin 1.1.9 to my Ender 3 which has the new 1.1.5 control board, but I cannot find a definition in the "boards.h" file. Any help would be appreciated. Thanks, Pat
View ArticleCopying files to Marlin SD over USB (no replies)
I have an Alunar M505 (Anet A8) with an older version of Marlin on it. I will be updating it when I understand more about how to do it. I am running Cura 3.2.1 because my laptop is W7 32bit, I will be...
View Article