Homing Problem SKR 1.1 Pro (no replies)
Hi everyone, I ran into a problem with my new SKR board which I not sure how to solve. I hope, someone can help me. I just switched the board of my printer from an Anet board to BigTreeTech SKR 1.1...
View ArticleMarlin bugfix 2.0 Dual Extruder problem (no replies)
I do not know if I am the only one with this problem, but after several hours of searching and I found no solution so I come to ask for help. I have an original board CR-10S with the stepper driver...
View ArticleBug: nozzle_to_probe_offset affects HOME-Z (no replies)
Printer: Delta / Kossel Mini - Firmware 2.0 latest The default : #define NOZZLE_TO_PROBE_OFFSET { 0, -10, -3.5 } affects the HOME-Z value. DELTA_HEIGHT is set (in my case) to 212.5 mm, but the printer...
View Articlewhich Arduino IDE to be used with Marlin (no replies)
Hi there, I recently had issues when compiling Marlin with different Arduino IDE versions. Since I was not able to find any information which version Arduino works with which Marlin, here is what I...
View ArticleUse E1 temp sensor pins for E0 temp readings (no replies)
Stats: mks gen L v1.2 running 24v using 100k 3950 thermistors on both hotend and heatbed. Running marlin 1.1.9 firmware. PID is generated using m303 command. Heat bed is working fine. I've used a...
View ArticleMarlin 2.0 lcd does not display correctly (no replies)
Hi everyone, My printer is an printrbot plus v2-1 (with wooden frame and a 20x4 lcd). I try to flash Marlin 2.0 but the lcd display shit like an overflow and all move constantly. LCD works fine with...
View ArticleMarlin Rumba Z Calibration problem. (1 reply)
Greetings to all. I am hoping some one might be able to assist with an issue I have been battling for 3 days over. Mr Google does not seem to be willing to give up the answer and I am just making...
View ArticleFolgerTech Kossel Stepper not responding (no replies)
I am trying to update the firmware on my FolgerTech Kossel to Marlin 2 in order to have thermal runaway protection. To do this I downloaded Marlin and modified an example kossel configuration.h file...
View ArticleSkr Mini e3 v1.2 Max31855 (no replies)
How do I use it? I have enabled it in config.h, but cannot find the pins to connect to in pins_BTT_SKR_MINI_E3.h.
View ArticleFilamentwidth sensor on MKS SBASE 1.3 problems (no replies)
Forgot to mention : Marlin 2.0 I run filamentwidth sensor on my k8200 without problems, and now i want to run one on my delta which have MKS SBASE1.3. But i can't for my life understand how to confure...
View ArticleAKL001-12 magnetsensor über mks gen 1.4 als Filament sensor nutzen? (no replies)
Ich haben einen 3D Drucker dort hat der Hersteller einen Magnetsensor ( repetier und duet) verbaut um das durchrutschen oder Stöckendes (AKL001-12 magnetsensor ) Filament Material zu erkennen . Diese...
View ArticleManual movements move X Y Z twice the amount. Prints are sized good though....
Hello everyone, My Problem: When not printing and I input gcode commands from any source (octoprint terminal, octoprint control menu, LCD, LCD terminal), to move my X, Y, and Z axis on my COREXY...
View ArticleStrange stepper behaviour (no replies)
Hello All, I have a Geetech delta printer and I just installed Marlin 2.0.x I have 200 step/rev step-motors with A4988 stepper modules. When I ask the printer to move in the Z direction in steps of...
View ArticleAdding ESP3D through ESP-01 to Ramps 1.4 (Marlin 2.0) (no replies)
Hi, i did some research on google and found no guide about Connecting to marlin through wifi. Chris Riley has a good tutorial here about adding ESP3D to Ramps 1.4 but as the date of upload shows its...
View ArticleDelta cart sags a little bit after homing (no replies)
Hi, one of the carts on my Delta printer sags a bit after homing. The others keep the endstops pressed but one of the carts sags more than the others after homing causing the endstop to be depressed....
View ArticleM900 = unknown command (2 replies)
I'm trying to enter the K value M900 for linear advance and get unknown command on both ponterface and octoprint. Anyone else experience this, is there a fix?
View ArticleCoreXY bed levelling points reversed causing inaccurate level (no replies)
Hi There, I have a Tronxy X5SA Pro CoreXY printer and I have replaced the board with an SKR1.4 Turbo running Marlin 2.0. The X and Y are homing correctly at the LF on the Min Stops. I have the bed...
View ArticleFunctional Marlin research for my core xy printer (1 reply)
I built a coreXY printer controlled by Marlin-1.1.8 and pronterface or repetierHost. I've been struggling for days to find the solution to problems that keep me going in circles. I would like to have...
View Articlemks gen L v1 and max31855 (no replies)
Hello. My friend wanna add max31855 on heater0 on Marlin 1.1.9 I set param -3 But when i compile it,ide give me exit status 1 'DIODIO53_DDR' was not declared in this scope Some know why,and if he can...
View ArticleBltouch not homing properly on SKR13 board (no replies)
Hi there! I'm working on a BLTouch upgrade for my printer and having difficulty getting the unit to work. When I turn the unit on, it glows solid red. When running a G28, the probe deploys but after...
View Article