Marlin build problem for Anet A6 (no replies)
Hello to the group, I have an ANET A6 and am trying to build the Marlin 1.1.9 firmware. I can build the firmware OK with Arduino 1.8.5 but with Arduino 1.8.10 I get the following:...
View ArticleZonestar End Stop Issues (no replies)
Hi All, I have "upgraded" my Zonestar P802M with a Rumba board and Marlin. It seems that all is ok, but every now and then the printer ignores the x-min endstop and it I have to hit the emergency stop...
View ArticleBLTouch and Marlin 2.0 (no replies)
How's it going, The other day I upgraded to the new marlin firmware (using an MKS Gen 1.4). Interfacing with pronterface I was carrying out an automatic bed leveling cycle and checking out the values...
View ArticleMore than 3 linear axis (UVW) with marlin (no replies)
Hey, I did a lot of research but I couldn't find out if more than 3 linear axis (XYZ) are finally implemented in Marlin? g2core has 6 linear axis for example (XYZUVW). There has been some works and...
View ArticleDamaged my motherboard and LCD on my T-Rex 3 (no replies)
Hi all, I want to share my experience and at the same time ask for your thoughts. I have a Vivedino/Formbot T-Rex 3. I have never updated any of my 3D printers before but it seemed simple enough, Or...
View ArticleToolchange swap Tool-numbers (no replies)
I have 4 Spoolholder fix in my printer and have 2 switching extruders (with a servo) Spoolholder 1 goes to left Lever of first Extruder, Spoolholder 2 goes to right Lever of second Extruder,...
View ArticleProblem with LCD in Marlin 2/Marlin2.bugfix (1 reply)
Hi, When i enable #REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER in marlin 2, it cannot compile/upload and gives following error: Arduino: 1.8.10 (Windows 10), Board: "Arduino Mega or Mega 2560,...
View ArticleDifferences SKR 1.4 and Marlin Compatibility (3 replies)
Hi all, I am wondering if the new released SKR 1.4 will have the same configuration as his old brother SKR 1.3 I am planning to get one of these SKR 1.4 + 2209 TMC Driver motors for modified Anet A8....
View ArticleMarlin 2.0.x - Hictop 3DP11/12 Original Hardware (no replies)
Converted Marlin 2.0.0 for the Original Hictop 3DP11/12 Marlin-2.0.0 Release.zip [attachment 113727 Image2.jpg] This is a basic conversion of the configuration files from Marlin 1.1.9BF
View ArticleMarlin Anet A6 printing problem . (no replies)
I have uploaded the Marlin 1.19 firmware with the BLTouch sensor added. The BLTouch autoleveling appears to be working OK. The problem is that when printing starts, the extruder nozzle is about 10 mm...
View Articlecompiling marlin for graphic display (no replies)
I'm trying to put a discount graphic display on my robo3d r1 plus. I downloaded from marlin the proper firmware. I take it to my arduino ide and it compiles with no errors. I commented out the LCD and...
View ArticleMarlin Anet A6 printing problem update (no replies)
Hi all, I have narrowed down my issue trying to print on my Anet A6 with Marlin 1.1.9 + BLTouch. If I command the the Z axis to Z0, the probe lowers to the bed, the BLTouch sensor seems to be...
View ArticleOdd Z axis issue (2 replies)
Hello, I've built a DIY 3D printer from my old CR-10 Melzi board, old some wood and spares from eBay. It's quite 'bodgy' as it is just used for experimentation, so I can keep my main printer (cr-10s)...
View ArticleMKS Gen V1.2 Marlin 1.1.9 Endstop problem (no replies)
I have an issue with Marlin 1.1.9 running on a MKS Gen V1.2. When I home my printer the Z axis homes correctly and sets a proper bed height, But when I begin a print job it ignores the Z endstop...
View ArticleMarlin 2.0.x Z-Axis Problem (no replies)
Hello everyone, I'm a newbie into Marlin and not really good at coding. Recently I wanted to add a filament runout sensor to my printer, so I wanted to enable it in the Marlin 2.0.x bugfix, but it...
View ArticleAnother Z Axis issue - Marlin 2.0.x (no replies)
I wondered if someone could shed some light upon this issue? Recently updated my AM8 with SKR1.3 and TMC2208s (which I previously had on Bugfix-2.0.x with no problem) to the latest stable release of...
View ArticleCleaning nozzle first print line changed position after Marlin upgrade (no...
After upgrading my Ender-5 with Marlin 2.0.x I notice a weird change. The first line that prints for cleaning the nozzle configured in Cura 4.4.1 starts printing at the upper right corner. After the...
View ArticleHow to implement physical buttons for special functions? (no replies)
Hi! I would like to add few physical buttons to my panel that would serve as a shortcuts for some functions. These buttons would be connected to unused pins of ny MKS SBASE board that is running...
View ArticleAxis don't move correctly on skr 1.3 (no replies)
Hi, I'm totally out of ideas with my cr10s upgraded to skr 1.3 If I try to home the X it doesn't home, it just make a weird noise on the Z steppers and doesn't move on neither Z or X. If I try to home...
View ArticleMarlin travel speed issue, movements are too fast (no replies)
Printer: Delta / Kossel mini (Atmel 2560, Ramps 1.4) After upgrading from Marlin 1.1.0-RC6 to current 1.1.9 (with bugfix) my printer moves with wrong speed. For testing I use a cylinder (d=30mm) with...
View Article