Marlin 2.0 newbie questions (no replies)
Hi, I am trying again to get marlin set up on an SKR board. I have both an SKR V1.3 and a Mini DIP V1.0. I had tried in the past but could never get the firmware onto the board. I did get a successful...
View Articlestrange behaviour after changing to marlin 2.0.5.1 (no replies)
hello. I am at a loss to know how to proceed with the following that came about after upgrading to 2.0.5.1. 1. No start signal detected- forcing start-- this comes up every time I connect the printer,...
View Articlewrong sensorless homing with TMC2130 driver on Anet A8 (no replies)
Hi everyone, Due to a failure of the motherboard of my Anet A8, I decided to upgrade it by installing the following kit : - Arduino 2560 R3 - RAMPS 1.6 PLUS - TMC2130 drivers on X,Y,Z and E -...
View ArticleUpgraded from Marlin 1.02 to 2.03 & 2.04 now Homing randomly failing Failes...
[attachment 114926 Configuration.h] - Pegasus 8 LCD -(Basic) [attachment 114927 Configuration.h] - Pegasus 8 LCD [attachment 114928 Configuration.h] - Pegasus 12 LCD I have (3) Maker farm Pegasus...
View ArticleMarlin dev-2.1.x with (lots of) TMC2130 shows 'TMC connection error' (no...
Hello all, I am having some trouble with my RAMPS 1.4 + RAMPSXB +self designed board. I am trying to run all 9 drivers with TMCs. Chip select signals for them were provided by 2 PFC8574 and a modified...
View ArticleZ auto-align question (no replies)
Trying to set up Z auto-align for the first time on a 320x320mm bed with a usable 300x300mm area. Could someone interpret what the positions are on the following statements? Thanks. #define...
View ArticleKeeping up with 2.0.x.x changes-need more details (no replies)
There are a large number of bug fixes, changes, and new features in stream of Marlin 2.0.x.x email updates but the comments are so brief like: New Controller Fan options and M710 G-code. Add M42 M to...
View ArticleAuto Bed Leveling - Error: Probing Failed - Marlin 2.0.5.1 (no replies)
Hi All, I tried to set up the Auto Bed Leveling at a homemade Graber I3 using Marlin 2.0.5.1. When I start ABL the probe is deployed, touches the table once and then is stow, causing the error: Error:...
View ArticleClik here to view.
Marlin 2.0.5.2 - Making it lightweight by disabling options? (no replies)
So I've been working on a pen plotter for over a year now. A lot of the machine is working really well now, removed the servo for the pen lifting and converted to a stepper motor for pen lifts now...
View ArticleSKR 1.4 weird connection problem to PC (Repetier) (1 reply)
Hi, I've changed the controller of my CNC from Ramps to SKR 1.4. I had several problems while compiling but I luckily I could solve them on my own. Unfortunately now I'm stuck. I use Repetier to...
View ArticleNewbie problem with Z movement in Hypercube setup (no replies)
As a newbie to both 3D printing and coding I am stuck with an issue and don't know how to try to resolve it. So far everything else seems to work but the Z movement is very odd. If I select Prepare...
View ArticleDRV8825 marlin 2.0 settings - configuration.adv.h (no replies)
Hi, I have an SKR E3 DIP V1.0 and I am trying to install some DRV8825 stepper drivers. I have the jumper pins set all to the right side (jumping red and black pins) and all 4 in place. I tried to...
View ArticleHoming Inverted after upgrade to Marlin 2.0 (no replies)
Hi Guys So i have updated to marlin 2.0 and my homing is now inverted? I coped my configuration.h from 1.1 exactly. If I load 1.1 everything is good again. What gives? anyone had this issue also? All...
View ArticleGet zeto position Gcode in Marlin (2 replies)
I was wondering whether there is a G-code in Marlin that does the same or something similar like the old M117 'Get zero position' command in FiveD? Or whether the old code is still available...
View ArticleMarlin configuration help (no replies)
I had been using Repetier firmware on my MKS Gen V1.4. I switched to Marlin because I is supposed to better support the tft35 controller. I have 2 questions. 1. Is there a way to put the status of the...
View ArticleMarlin 2.0.5.x inconsistent speeds pen plotter with G02/G03 (no replies)
Hi all, so this DIY pen plotter is coming a long way but I keep getting slowdowns in some of the gcode files that I feed to it. For example, one file is about 3Mb and it runs fine, but the other file...
View ArticleG28 ABL first probing speed (no replies)
Is there a way to slow down the first fast Z home probing (G28), without affecting the probe pull up speed, or making the pull up faster, without affecting anything else? (Marlin/src/module/probe.cpp:...
View ArticleMax softwareserials on Mega2560 (no replies)
Hello there, I've been working a while now on an 3D-printer specialized in paste materials, mainly clay. I've been expoloring extrusion methods and ended up with an mechanical extrusion system (one...
View ArticleMarlin display help (no replies)
I have a 12864 controller. I changed the extruder fan to be temperature controlled. When I did that the fan icon and %speed got removed from the screen. That's no problem because the fan comes on at...
View ArticleAnet A8 + Reprap discount smart controller on marlin 2.0 (2 replies)
Hi guys, ordered a replacement for my lcd, but got REPRAP_DISCOUNT_SMART_CONTROLLER instead, I wonder if I can use it. So, what I did: #define SDSUPPORT #define REPRAP_DISCOUNT_SMART_CONTROLLER...
View Article