The issue of communication between Marlin board and Android OS (2 replies)
I would like to use an Android tablet to communicate with marlin board(STM32F40 or LPC1768). The physical interfaces of the boards are Type B usb, and the tablet have both USB host and rs232. I have...
View Articleresuming after the power loss, but Z-axis is not moving up (no replies)
Hi, Anyone using Marlin Power loss recovery with the 1.1.9 Marlin? The print is resuming after the power loss, but Z-axis is not moving up. It is printing in the same layer where the print was...
View ArticleProblems with MKS Robin E3 with BLtouch, in Creality Ender 3 PRO (no replies)
Hello everyone, everything good? I use Creality Ender 3 PRO. I bought the MKS Robin E3 board and managed to install the Marlin firmware normally. However I tried to install the BLTouch sensor together...
View ArticlePlatformIO compile error (1 reply)
Hi there. I have tried with the firmware version 2.0.6 and 2.0.6.1 as well with older version that failed to compile with PlatformIO. I'm using Windows 10 and the platformIO version 1.48.0 Apparently...
View Articlecant verify marlin 2.0.x to arduino Due (2 replies)
as the title says i cant verify marlin 2.0.x to a arduino Due [github.com] here it says it supports the due. DUE version 1.6.12 on the Arduino IDE (1.8.13) i keep getting the error Arduino:1.8.13...
View Article:(error: request for member 'print' in '3', which is of non-class type...
So as you can see VSCode says NO FIRMWARE FOR YOU ! And shoots me out some computer mumbojumbo I dont understand lol I need serious help I've been at it for 4 months and everywhere I ask either goes...
View ArticleVSCode Setup & Installation for Ramps (3 replies)
I am ready to start the installation of VSCode / PlatformIO venture again! The first time I installed VSCode / PlatformIO was having problems problems with installing Visual Studio 2017-2019 as the...
View ArticleTMC2208 Y Axis Sometime Doubles Movements and Speeds (no replies)
Hi folks, I'm having this wierd issue at the moment with my printer (Wanhao i3 V2, SKR 1.4, TMC 2208 UART @ 1/16, Bltouch, Marlin 2.0.x) where randomly the printer will move double the distance and at...
View ArticleI have issues with UBL not seem to correct at all (no replies)
Hi all, I have Marlin 1.1.9 and I have an inductive sensor, and I managed to get to this result with G29 P1: Recv: 0 1 2 3 4 5 6 7 8 9 Recv: 9 | +2.287 +2.817 +2.732 +2.668 +2.622 +2.417 +2.455 +2.257...
View ArticlePrinter prints mirrored object (2 replies)
Dear all, I am facing following issues in my Hypercube 3D printer: 1) I am using Hypercube 3D printer. Whenever I prints, my object gets printed as mirrored object. So I tried to invert directions of...
View ArticleProblems with updating to marlim 2.0.6 (2 replies)
Good Morning! I have a 3D of my own construction and I use RAMPS 1.4 as a controller. with marlin 1.1.x it is working well. When I update FW to 2.0.6 I start having problems with auto leveling. I send...
View ArticleMKS Gen L V1.0 - DRV8825 (no replies)
Hello Everyone, I have bought a board to add it to my custom 3d printer. MKS Gen L V1.0 Board. MKS Gen L V1.0 Picture and i received it without a stepper drivers XD i bought DRV8825 right now. I have...
View ArticleRelease Marlin 2.0.7 (no replies)
Marlin 2.0.7 New Features MarkForged kinematics (#19235) New Machines and Boards Teensy 4 (#19311) MKS Robin E3P (#19442) BigTreeTech SKR E3 Turbo (#19500) MKS SGEN L V2 (#18822, #19462) MKS Gen L...
View ArticleMarlin 1.1.x bugfix homing issue (no replies)
Hello all, I have the Tevo Tornado 2018 gold edition printer. This printer used the MKS_Gen_L 1.0 board and A4988 Green version stepper driver chips. I upgraded this printer to a E3D v6 Gold hotend...
View ArticleErrorrinter halted. kill() called! [ERROR] Errorrinter halted. kill() called!...
hi all tried my luck at the pronterface forum- alas, no luck there……. need help here- Pronterface keeps shutting down my " prints" after 3 cycles, motors move normally- with the KILL message: Print...
View Articlenozzle probes off bed (no replies)
i just added piezo probe to my tronxy x5s . nozzle homes about 20mm left of bed, thats normal position. when i try to probe the bed with nozzle it tries to probe in 0,0 coordinates. tried every...
View ArticleMarin 2.0 + Mks Sbase 1.3 - Ethernet port (no replies)
Hello, I have an MKS SBASE 1.3 board with Marlin 2.0 running ok. The problem that I'm having is that the network port on the board is not working with Marlin, juts for testing, I have installed...
View ArticleMarlin managing current differently in 2.0.x?? (no replies)
I upgraded from Marlin 1.9.x to 2.0.7. - I am using an Einsy Rambo with integrated TMC2130 drivers. I literally used the same currents from the 1.9.x version on the 2.0.7 and the motors barely have...
View ArticleAurdino issue (Some of unanswered queries from previous post) (no replies)
also in pronterface I get message that "Error: volume. init failed" and also sometimes I couldn't print some object of due to memory shortage. That time I reduces the scale of object and then It gets...
View ArticleAnycubic Chiron Help LPC1769 BTT SKR 1.4 Turbo + Stock Screen (no replies)
Hello Everyone, I am hoping to find some answers to why I cannot compile firmware for this setup. Starting with this fork of the Marlin Bug-fix-2.0.x firmware made by SwiftNick - Full Chiron Support...
View Article