Noob Question on Arduino (1 reply)
When I try to load a Marlin file into Arduino in Windows all I get is the first "Marlin" Tab. The other tabs to the right (Config H, etc.) are missing. What am I doing wrong? Everything is there when...
View ArticleG28 works but G29 fails with false triggered probe. (no replies)
I have issues with my marlin 2.0.7.2. It has worked fine before I got my final tmc2208 soldered to get rid of error all low with M122 running UART BOARD BIGTREETECH SKR V1.4 X AND Y TMC2209'S...
View ArticleFan override (no replies)
Hi all, I don't like to print ABS nor PETG. It gives me always hard time. Today I print same part 4 times as you can see 2 big clamp hold it for warping but the biggest problem start after printing...
View ArticleWrong Temps with NTC 3950 100k Thermistor (no replies)
With the recent firmware for my SKR 1.1 Pro board I couldnt get the thermistor working properly. Its a NTC 3950 100K Thermistor and i am supposed to use this entry in FW: 11 : 100k beta 3950 1%...
View Article4.2.7 board with TMC2225 (no replies)
Hi, How should I compile Marlin with an Ender 3 v2 board with 4.2.7 and TMC2225? I noticed that TMC2225 are not officially supported by Marlin. Shall I use TMC2208_STANDALONE? What issues can that cause?
View ArticleMKS SGEN L + hotbead temps and cooler on\off if bed temp > 90 (no replies)
Hello. FW: Marlin 2.0.8 bugfix board. MKS_SGEN_L hotbead: mk2b ( PCB ) 12v bead is heat to 110 celsius - normal but when i start printing and cooler turns on hotbead cant holds 90+ so, i want...
View Articleendstops always on per endstop? (no replies)
hello i install 6 endstops for safety, so i need to enable ENDSTOPS_ALWAYS_ON_DEFAULT but my bed is lower than the Z min endstop. how can i go past the endstop but only the Z min? thank you Illogique
View ArticleMarlin G code units mm/s vs mm/min (no replies)
Hello, I'm making a diy 3d printer. I have a RAMPS 1.4 board with Marlin firmware 2.0.7.2. This goes pretty well, but I'm confused by the units for feedrate and acceleration. In the Marlin...
View ArticleReadjust printer with Marlin (no replies)
Printer manufacturers won't give you conf file. In this case what to do? I need turn on linear advance and: 1.- Set the steps/mm of the extruder between 900-600steps/mm. Initially recommended...
View ArticleHeater issues (no replies)
During a filament change, M600, the heater cools down by about 10-15 degrees, which is to be expected, and when the filament is loaded the heater tries to warm up but cannot achieve it's desired...
View ArticleHoming with Marlin Firmware (2 replies)
My issue is that I'm trying to home at the left front corner on my printer but when I home it goes to the right rear corner. My end stops for the X and Y are Max end stops and the end stop for Z is...
View ArticleAuto fan start when extruder temp >50C - disables M106 !! (2 replies)
I am running 2.0.5 bugfix and want the part cooling fan to come on when the extruder temp is >50. So, in configuration_adv I have defined the following :- #define FAN_KICKSTART_TIME 500 and #undef...
View ArticleUBL Auto Leveling - setting to cover the bed (no replies)
I am having difficulties to understand how to set up UBL to cover as much bed as possible. I have not square bed 250x290, but my probe can reach all of it ( not as nozzle but close) I understand that...
View Articlex and y vibrate when moving to the z safe homing point (no replies)
X and Y vibrate and move erratically when moving to the Z safe homing point X,Y, and Z all move smoothly when moved individually. X and Y both HOME smoothly The problem occurs when X and Y move from...
View ArticleMarlin waiting for restart after failure, wont allow reconnect (3 replies)
When probing fail, and printer enter KILL state/ disconnects. Previous Marlin 2.x on Atmega 2560 allowed reconnection, starting over Newer Marlin 2.x on Bigtree STM32 controller require physical...
View ArticleHelp power loss recovery causes layer shift (no replies)
I have a Corexy running Marlin 2.0.7.2 bugfix a BTT mini UPS on a SKR 1.3 with end stops with TMC2209 drivers. I do not use the driver sensor less to maintain accuracy. Problem when there is a power...
View ArticleExtruder stops working and then weird messages show up in serial (no replies)
Hi there, I've got a printer that has a problem with the extruder stopping during a print. When I take a look at the problem, I find a bunch of messages in the serial output that look like...
View ArticleLCD not working with SKR 1.4V turbo (1 reply)
Hi , We are connecting LCD2004 to SRK-V1.4, but we see LCD is not displaying any data. On probing we found the Enable and RS pins on LCD section are not proper RS signal is always high and low and EN...
View Article[SKR PRO 1.1/TMC5160] Motors randomly stop working until power cycle (2 replies)
Hello, I am having an issue with my homemade core xy, running an SKR 1.1 PRO with TMC5160 drivers. I am using the marlin 2.x branch, commit 1d631b72801174b29e2d5cb2115022a194ed303b from November 21st...
View ArticleBltouch not retracting (2 replies)
Hi, I am trying to get a bltouch working on my cr-10s v2 board. I have it installed and plugged in like the multitude of videos I watched and the instructions show. My voltage is above 5v, the thing...
View Article