compiling 2.x: avr-gcc: error: CreateProcess: No such file or directory (1...
so trying to compile 2.whatever to upgrade from 1.0.something, and i cant seem to compile. first errors i was getting were identical to here, so i changed my temp directory, renamed folders, moved...
View ArticleHelp with 3dtouch config in SKR1.3 (1 reply)
Hi, I'm hoping someone can help. I'm trying to get a Bigtreetech 3dtouch working with the SKR1.3. I've gone through dozens of youtube videos, and message boards/troubleshooting and nothing seems to...
View ArticleHoming Issue in SKR 1.4V TURBO (no replies)
Hi sir I am facing a problem with auto homing. when ever I do auto home the x,y,z move 1 cm and stops that to in opposite direction please help Thanks in advance
View ArticleFilament change function - LCD touch (no replies)
apologies if this has been covered before I would like to implement filament change M600 but without a simple LCD there doesn't appear to be a way to acknowledge the change has occurred and the print...
View ArticleAdvanced pause feature - strange behaviour (no replies)
Hi guys, 'm kind of deperate getting the advanced pause feature issued by an M600 to work the way I expect it to. I'm using Marlin 2.0 on an Ender 3 and here is what my configuration of the feature...
View ArticleChanging to print screen while printing (no replies)
Currently I have an Ender 5 Plus with Marlin 2.0.6.1 installed on a Big Tree Tech SKR 1.4 Turbo and TFT35 V2.0. The TFT is touch screen only, so not sure what impact that has, but when I start a print...
View ArticleGeneral (no replies)
I have a CR10 S5 printer that was purchased around 2017-18. I've never used Marlin before and I'm trying to upgrade my printer's firmware with Marlin 2.0. When I compile the configuration code I get...
View ArticleCustom probing points MK52 bed (no replies)
Hi, I have been figuring out that I'm doing something wrong. Using a custom built Prusa MK2S with a MK52 heated bed. I'm using #define AUTO_BED_LEVELING_BILINEAR in Marlin 2.0.6.1 and need to define...
View ArticleSKR Pro v1.1 SD card issue (no replies)
Hey everyone, last weekend i added a new silicone heater (450W) and a new 600W PSU to my DIY printer. Before it printed fine all night long without any issues besides the bent heated bed. After the...
View ArticleZ_MIN always triggered (no replies)
I have a new motherboard I am trying to get working. It is a MKS SGEN_L V2.0 board with MKS TMC2208 drivers in UART mode. I have a 3DTOUCH probe as well. My first issue is the Z_MIN setting is always...
View Articlehow is X_CENTER/Y_CENTER defined (no replies)
Looking at the z_safe_homing section in the configuration.h file and it has #define Z_SAFE_HOMING_X_POINT X_CENTER. Where is it getting the value for X_CENTER? Same for Y_CENTER. It used to use a...
View ArticleZ Fade Out (no replies)
Hi, I have a home built 3D printer, which is working ok. It uses Marlin 2.0.x bugfix, and mega2560. The question i have is regarding bed levelling. I have auto bed levelling installed and working, and...
View ArticlePrinter moves 20mm instead of 10mm? (1 reply)
Hi. I installed Marlin from the GitHub Tronxy Tree on my TRONXY X5SA Pro 500. I uncomment the right printer in the firmware. I changed the number of Z-motors in the configuration.adv from 1 to 2 and...
View ArticleSPI OLED on SKR 1.4/1.5 and Re-ARM LPC1768/9 based boards (no replies)
How to get a working tiny SPI OLED 0.96", 1.3", 1.43" (and so on...) with a SKR 1.4 Turbo, and probably other unsupported boards. I²C OLEDs cause a lot of issues with the SKR 1.4 and 1.5. It will be...
View ArticleAnycubic i3 Z-offset (2 replies)
Hi everyone, I'm trying to finally resolve an issue that has plagued me for a long time regarding BLTouch and my Anycubic i3 Mega configuration. It seems no matter what I try I'm unable to get the...
View ArticleHow to let Marlin know the print job is completed? (no replies)
I am using ADVANCED_PAUSE_FEATURE and ADVANCED_PAUSE_FEATURE After a job is successfully completed, and all heaters off, the Marlin (display) still offer to pause or cancel the job. On cancel - it...
View Articlez probe is triggered but homing crashes head into plate (4 replies)
hello my configuration is a Ender 3 with SKR1.4 mainboard and Marlin 2.0.7.2 and TMC2130 stepper drivers seem unable to get the z-axis to home properly. Wanted to use the stall detection of the...
View ArticleUnable to upload Marlin to Mega2560 clone (7 replies)
Hey I'm currently making my first 3d printer and I went with the cheap option of mega 2560 + ramps 1.4 clone set. As one might guess I'm quite unexperienced with this arduino stuff. So when I try to...
View ArticleHow to establish 0,0,0 in marlin. (3 replies)
Setting up Marlin 2.x.x on my CoreXY Hypercube build and where do you establish "home" in congiguration.h . When I do a G28 to test the print head goes as expected to the front left of the print bed....
View ArticlePuzzled by my results with M600 - some help would be appreciated (4 replies)
I have a Anycubic Kossel Linear Plus, with a Trigorilla board running Marlin 1.1.9 - this has been running nicely. Now I have been wanting to use M600 (filament change), and I've *almost* got it...
View Article