CoreXY and Max endstops (1 reply)
Hi again, I am building a corexy machine that uses max endstops for x and z and min endstops for y. Here's my issue: if I set all endstops to home to -1, and I keep the section called...
View ArticleZ-probe configuration in Configuration.h (1 reply)
I'm trying to get Marlin 1.1.0-RC8 working on my DeltaMaker delta printer to replace the much older Marlin firmware the printer came with. Have everything working except the z-probe. The way this...
View ArticleRC-8 issues (1 reply)
I tried to download the new RC and just using the stock version from the github page I cannot verify it out of the gate. It gives me this message: Arduino: 1.6.13 (Windows 10), Board: "Arduino/Genuino...
View ArticleAfter setting up auto bed leveling, printer loses reference to home (2 replies)
Hi, I have a Folgertech i3 2020, running a ramps 1.4 and Marlin 1.0.2 firmware. I installed a inductive sensor for bed leveling and went through the setup on that and got the probing working fine....
View ArticleNeed some help with steps/mm (4 replies)
I'm running Marlin 1.1.0 RC7 on my newly minted D-Bot Core XY and I have some issues with the steps/mm settings. I'm using the DRV8825 drivers with the MS3 jumper set which essentially means they are...
View ArticleZ axis will not respond to homing command (Mendel90) (1 reply)
I'm having an issue with running G28 commands on my Mendel90. Sending G28 homes the X and Y axis but Z axis does not move at all. Sending G28Z also has no response from the printer. Sending G0Z...
View ArticleAuto bed level unstable (5 replies)
Is there a reason I have to keep changing the Z-offset for auto bed leveling? Having given up totally on my Delta printer, I thought that since I had the sensor, I might as well install it on my...
View ArticleAzteeg and Viki2 with RC8 (no replies)
I have a stable working RC7. This weekI have tried to update to RC8 and RCBugFix. When i click the encoder on the viki2 controller I get a crash- Killed. message on the LCD. Can anyone else with an...
View ArticleMarlin PID temperature control code isolation (no replies)
Hello all reprapers! I'm currently working on a project where I need to control the temperature of a metal block using a 40w cartridge heater and 100k thermistor. at the moment I am using an arduino...
View ArticleRC7 BED_LIMIT_SWITCHING (no replies)
Hello, I Use Marlin RC7. In the confi.h-file under the section "PID > Bed Temperature Control" is the following function: Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING...
View ArticleMarlin RC8 AUTO BED LEVELING BILINEAR (1 reply)
Hi, just a quick question 'cause I am not sure about this feature. Is it possible to save the mesh data to eeprom - like in the UBL version of Marlin? Marlin wiki says it throws the data away - but...
View Articlehow to change g28/29 code to include the probe deploy/stow (1 reply)
Anybody out there got any idea how i can change g28/29 code to include the probe deploy/stow in marlin so its permanent in my marlin firmware?? that would certainly help alot of people out that are...
View ArticleBilinear bed leveling and associated gcodes and procedure (4 replies)
Hey guys, I made the move from rc6 to rc8 and have configured to use the bilinear bed leveling. By issuing a G29 my machine begins probing and goes through its probing routine. I see the resulting...
View ArticleInduction Z Probe on Z Max, NOT Z Min (1 reply)
Hi, I think I am reading too much into the keywords that contain "Z_MIN*" to mean the Z Minimum limit switch pins... I am on Marlin RC6. I am using proximity sensor (NPN) at 5V connected to Z Max My...
View ArticleInductive probe doesn't recognized as the Z endstop (no replies)
Hello all, I use a Prusa i3 with a Ramps 1.4 and an inductive probe on Z axis. I recently update the old version of Marlin firmware for Marlin 1.1.0 RC8. I have one problem with this new version: the...
View ArticleAuto Bed Leveling Setup issues - I don't understand :-( (6 replies)
Hi Guys (and girls) Ok. I have an ANET A8 chinese knockoff and after a number of THEIR driver boards being bad, I replaced it with a standard R.A.M.P.S setup and I FINALLY got it printer "printing",...
View ArticleZ probe repeatability - no data (3 replies)
I enabled z probe repeatability in the firmware, but when I run a M48 command, I get all 0s: SENDING:M48 n10 V4 M48 Z-Probe Repeatability Test Positioning the probe... echo:busy: processing echo:busy:...
View ArticleMin Temp not lower than 76ºC (no replies)
Hi, This problem does not really affect my prints, but my curiosity would come down if I understand why this is happening. I am currently using a P3Steel printer running with Arduino Mega, RAMPS 1.4...
View ArticleMarlin Diamond Hotend (1 reply)
Hey! I have a Prusa i3 Hephestos and I will install the Diamond Hotend soon. I have a question regarding the firmware. At reprep.me they recommend "Marlin - The Diamond Hotend version" [github.com] I...
View ArticleAnyone know if a RUMBA, CoreXY and Marlin RC-8? (1 reply)
Anyone know if this combination will work together? thank you
View Article