Marlin 1.1.0-RC7, looking for setting location after homing (no replies)
I am wondering where is the setting to set the location after homing. My delta decrease the Z about 40 mm after homing sequence finish. Anyone know where the setting to change that 40 mm distance is?...
View ArticleZ axis issues (1 reply)
I am currently having issues with my z-axis. I am unable to perform both a G28Z command and a G0Zxxx command. My steppers (two steppers for z with 8mm acme screws) just buzz briefly then stop. It...
View Article(ASK) Delta printer, understanding nozzles position and probe position...
Delta printer with 2 nozzles and Touch probe. All positions below are relative to center of the bed which is X:0 Y:0 - The first nozzle is at X:-10 Y:0 - The second nozzle is at X:10 Y:0 - The probe...
View Articlehooking up lcd smort controller to new marlin issue (no replies)
im trying to do away with the chinese stuff on my chinese reprap i have bought the smart controller the ramps and a new arduino to start fresh i have downloaded the new and old version of marlin and...
View ArticleMarlin first print help (1 reply)
Trying first print after converting my DaVinciDUO with RAMP 1.4 and Marlin. But when I begin print, the extruder moves away from home to a random: X 82.22 Y 103.30 Z 0.30 Not sure why it's moving away...
View ArticleMarlin Update Question (4 replies)
I have a Melzi board with Marlin v1 on it and would like to update it to the latest 1.1RC to get some of the new features. I have done alot of searching but can't quite answer my question. Can anyone...
View ArticlePause the print process ? (1 reply)
Suppose I had designed an electronic filament detector that gives a LOW signal or a HIGH signal (5 Volts or 3.3 Volts) in case the filament broke .... How would I make the Microprocessor on my...
View Articleadjusting bed fan pwm frequency (no replies)
Can i adjust the bed fan pwm frequency in the firmware? I've looked through config and config_adv but nothing obvious is leaping from the screen. Unfortunately my bed fan won't run at less than 90%...
View ArticleMesh bed leveling - Z axis not moving during print (3 replies)
Greetings, So I have a 3D printer of my own design, hbot with moving Z-axis bed, running the latest version of Marlin. There are two steppers moving the bed up and down via threaded rods. I recently...
View ArticleAuto Nozzle Height (Z-Offset from extruder) (no replies)
I am wondering if there are any existing versions of Marlin that incorporate auto nozzle height. I really want to have this feature because every time I switch the nozzle on my printer, I end up...
View Article(RAMPS)Hotend change pin from D8 to D10 (3 replies)
Hello guys. I have a problem with Mosfet on pin D8 in my Ramps 1.4. I would like to change it to another from heatbed or cooler because they works well. I changed it in definition in pin_ramps.h by...
View ArticleWay to bookmark GCode commands for use with LCD screen? - Z calibration...
Hi all Im trying to find a way to "bookmark" / shortcut some GCode commands Actually 3 commands in 1. G28;G29;G1 Z0 Basically auto home,level and go to Z0 ... i use this for calibrating z offset but...
View ArticleMarlin RAMPS Issues (no replies)
I've been building a custom 3d printer, and have some issues that I can't seem to solve. The Full Graphic Controller says the hotend temperature is always around 173 C, and the card always says either...
View ArticleAny Experience for SD Card Logging (no replies)
Hi, Any experience for logging to recover failed print? If we log what all gcode steps with error codes, we would recover our half printed items. Best Regards
View ArticleExtruder fan controled by 2nd extruder output (2 replies)
Hi all as title I want to connect the extruder cooling fan to the second extruder outlet so that the fan will only turn on when it gets to a pre-set temperature. Is this possible? if so what do I need...
View ArticlePID autotune timeout, remove code from Temp.cpp (no replies)
Hi, first off I have looked at the other PID autotune threads and they do not explain my problem.....so here it is. Also, as a note, the printer works....not as well as hoped but I am still getting...
View ArticleCommande G code M503 ne renvoie pas de valeurs (no replies)
Bonjour, J'utilise une Reprap guru, sur un Imac, Repetier Host version 1.02. Quand je lance une commande M503, je n'obtiens pas les valeurs attendues mais une ligne de ce type : > 5:44:01 PM: N17...
View Articlemarlin configuration problem (no replies)
Hi,I have a Ramps 1.4 setup on a chinese Aurora I3 printer. After fitting a bowden type extruder,tyring to update the settings I ran into the following problem. When trying to upload the sketch to...
View ArticleY axis will not home! (CoreXY, Marlin) (3 replies)
Maybe someone can point me in the right direction. My y axis will jog, but sending "home all" results in homing of z then x, and not Y. Is it a power issue? My stepper drivers are all set around 1.3v...
View ArticleCompiling Marlin on Raspberry Pi (Raspbian Jessie) (2 replies)
When I try to compile a feshly cloned Marlin 1.1.0-RC8 on my Raspi3 (by entering "make" in the Marlin directory), I immediately get make: *** No rule to make target 'applet/wiring.o', needed by...
View Article