POWER_LOSS_RECOVERY do not work properly (no replies)
Hello, I pause the print then turn off and wait a while and turn it on again however there is not resume print. I defined POWER_LOSS_RECOVERY but it does not work and I am sure power loss recovery is...
View Articleexternal input for cycle tart (no replies)
Need Help for External input cycle start for repeat job
View ArticleHelp with Configuration IDEX machine Marlin 2.0.9.1 (no replies)
Hi Folks! Does someone have an example configuration.h and configuration_adv.h for an IDEX configuration? I have never configured a Marlin before and I keep on getting errors on compiling. Something...
View ArticleMarlin- change Y axis pins on skr1.4 board (no replies)
Hi all, Wondering if anyone could help me with Marlin configuration. I'm trying to upgrade the board on my MK3s bear to a BTT SKR 1.4. There is something wrong with the port for the Y axis. It just...
View Articlefan multiplexing ? (no replies)
I have just seen that there's a fan multiplexing define could someone please tell me what its used for ? Thanks Nikki
View ArticleM851 not working (no replies)
Hi all! I have my TRONXY running fine with dual Z endstops and BLtouch since 2019. Now suddenly (?) M851 does not work. EEPROM is of course enabled. No matter the value of M851, the nozzle prints at...
View ArticleHome made 3D printer, extruder motor not working (1 reply)
First of all, sorry for the bothering and if this issue was already reported somewhere, and somehow slipped trough my search in the web! So, I got a 3D printer home made and the extruder motor doesn't...
View ArticleAfter Resume Z is too close to printed model (no replies)
Hello, I start to print something then I pause it and after I resume it is too close to printed model how can I increase z after resume? I tried to increase #define POWER_LOSS_MIN_Z_CHANGE 0.05...
View ArticlePower On Macro (no replies)
Hello, I am attempting to create, and use, a macro for when my machine powers on. The code I am using is listed below. It compiles just fine however, the machine does nothing when powered on. Any help...
View ArticleAdd more than 4 servos MKS GEN L v1.0 RAMPS 1.4 (no replies)
Good afternoon, im building a system with marlin firmware and i want to connect more than 4 servos. The board i have is the MKS GEN L V1.0 wich has RAMPS 1.4 built in, this one has 4 connectors for...
View ArticleZ offset after delta auto calibration (no replies)
I'm a little confused so my delta does about 4 Iteration's so after that's done I assume I store the settings? So maybe I'm missing something how would I know my offset?
View ArticleBacklash calibration using a conductive metal cube? (no replies)
I have been messing with the backlash setting in Marlin and got it dialed in pretty well for the belt driven triple Z axis on my printer. I noticed there is a setting for automatic calibration using...
View ArticleOwn 24V UPS / Auto #define THERMAL_PROTECTION_BED 8-) (no replies)
Hi everyone. I am not a programmer but I need to carry out something. I am sure a programmer can handle this in under minutes. I only setup up Marlin / and change pins etc / but now I need a serious...
View ArticleUpdating Marlin in a Black Widow, TMC2130, Filament Sensor.. (no replies)
Hi, newbie here looking for help After years of service i want to update my TEVO Black Widow, I have only flashed the firmware once, to install BLTouch. This time i want to make the following changes:...
View ArticleHow to setup second independant serial port on Marlin 2.0.9 (2 replies)
Hi, I'm new to the Reprap forums. A bit of history about me, I'm an electronics tech at work and I've been exploring 3D printing as a hobby for about 2.5 years. I've built my own core XY printer and...
View ArticleI need help building for Elegoo Neptune 2 (no replies)
I'm trying to build Marlin for the Elegoo Neptune 2. I'm using the MKS fork at [github.com] using the mks_robin_nano_v3_usb_flash_drive environment. I've manage to build something with PlatformIO on...
View ArticleSimple Command line through pins (Ramps 1.4) (no replies)
Hello there, I have a question, I cant seem to find an answer to. Is it possible to send a simple command through the ramps 1.4 board pins? For example, turn the fan on/off with the m105 command...
View Articlehelp programming bed size (4 replies)
Hey, I upgraded my cr10 with an SKR 1.3V board running Marlin bugfix 2.0.x But it's crashing the X and Y every time I start a print I set the bed size to 300mm as seen in the image but soon as the...
View ArticleSidewinder X1 with Marlin 2.0, no designations for hot end/part cooling fan...
Hello all, I'm new here. New to 3D printing, new to compiling firmware and new to coding. I recently bought a used Artillery Sidewinder X1 and after the main board took a dump on itself, I decided to...
View ArticleZ_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS (1 reply)
I have a question on where the Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS should be measured from/to. I have a bed that is 535x535 with a printable area of 490x465. Z1 is -95,0 Z2 is 565,0 (+75 on x) and...
View Article