Marlin 2.0.9.3 & Build surface alignment (1 reply)
Hello, I Have been upgrading an Anet A8. I am having Three basic problems with my build that I just can't quite figure out; All Three problems seem to stem from the same origin, I would truly...
View ArticleBabystepping not moving not matter what (no replies)
Just complied bugfix 2.0 from last week, flashed my Artillery Hornet but now Babystepping does not move no matter what direction or amount. any ideas greatly appreciated. #define BABYSTEPPING...
View ArticleBTT TFT 3.5 not seeing printer (2 replies)
Hello I have a ender 3 pro and just installed a BTT TFT 3.5 screen. The screen tells me "no printer attached". Ive tried all the UART speeds to no avail If I go to the marlin side and tell to load...
View ArticleMarlinTarantula-EasyConfig-1.1.x wrong extruder fan (1 reply)
Stock Tevo Tarantula single extruder small bed Running Jim Browns MarlinTarantula-EasyConfig-1.1.x (MarlinTarantula-EasyConfig-2.0.x freezes during compiling) When print starts Fan 2 starts (I don't...
View ArticleMKS Gen L problems. (3 replies)
I have a FLSUN i3 printer with an MKS Gen L v1 mainboard. I am at the end of my rope as I have been trying to get this printer running for over 2 months with no success. it had been running for 5...
View ArticleMarlin 2.1 (3 replies)
The latest Marlin bugfix is at 2.1 and includes MPC (Model Predictive Control) for the hot end. This is a replacement for PID, and it does an amazing job. The same gentleman who developed it also...
View Article#error "PULLDOWN pin mode is not available on AVR boards." (1 reply)
Hello Can anybody help with this. My english is not so good, but hope you understand my issue. If i try to build test Marlin autobuild with basic settings it works, but if i copy(overwrite) from...
View ArticleManual mesh bed levelling (1 reply)
Hi :) No i have new issues with manual mesh bed levelling.::o I define these rows #define PROBE_MANUALLY #define MESH_BED_LEVELING #define ENABLE_LEVELING_AFTER_G28 #define MESH_INSET 15 #define...
View ArticleEC11 encoder configuration issue (no replies)
I am upgrading Velleman Vertex K8400 printer and replacing original 8-bit motherboard (3Drag Controller) with BTT SKR2.The original firmware was Marlin version 1.4. On SKR2 I will be running the...
View ArticleLines between Items When Engraving (no replies)
I'm having an issue with a Marlin-based laser cutter I built. It seems the laser doesn't turn off between items (picture attached). From my homework so far, these unwanted lines are G0 moves with no...
View ArticleFirmware or Motherboard issues? (no replies)
Hi! So I'm currently working on building a prusa i3 mk3 clone with an einsy rambo board with TMC2130 stepper drivers. Everything was working fine last Friday, the bed was heating, the axes were moving...
View ArticleLCD menu slow when selecting a file to print on SD card (2 replies)
When controlling my printer from the LCD encoder I find that in all of the menus (bar one) the movement of the highlighted line is responsive. However, in the "file to print" menu it is a lot slower...
View ArticlePrinter halts at first Z-probe attempt (no replies)
I upgraded my CoreXY printer's mainboard to SKR2 Rev.B and having troubles configuring ABL feature. I have z-probe of my own design with optical sensor and electronic circuit identical to the circuits...
View ArticleBootscreens (1 reply)
What is the actual compile process for the Marlin bootscreen? Under Color_UI, I cannot compile the full 480x320x16 bootscreen due to lack of flash space. Setting the bootscreen to small compiles and...
View ArticleBL Touch Issue (1 reply)
Ok so here is my issue I have an ender 3 with a BTT octopus v1 board with TMC2209 drivers and a BL Touch. I cant get the BL Touch working correctly I have tried all I can think of. Sometimes it will...
View ArticleZ axis does not respond to step change (2 replies)
Have a problem with my 3D printer. I modified the Z axis to 1/8 of a step and no matter what the value entered in the steps/mm section, it keeps moving the same incorrect distance. Any tips? Ty.
View ArticleProblems Auto Homing Endstop Max (5 replies)
Dear community, I built my own 3D printer. The limit switch for X is on the right side of the printer, i.e. Endstop_Max. The stepper is also installed on the right. The limit switch for Y is in front,...
View ArticleMarlin X5SA Pro (no replies)
hello I have a Tronxy X5SA Pro, I changed the firewall to marlin because it wouldn't let me modify parameters, when I try to print everything starts fine until the first layer then only the extruder...
View ArticleMarlin 2.0.9.3 and Anet A8 2004 LCD (no replies)
Hi. I have Anet A8 with Tatara Hayabusa frame, Mega 2560 and RAMPS 1.6 I had Marlin 1.9.9 that was working fine, but I changed my hotbed to bit larger one and had to adjust few options. As there is...
View ArticleTrouble Running NEMA 23 motors (no replies)
I'm trying to run a NEMA 23 motor off a mega 2560, ramps 1.4, and an em556s driver. The motor moves but very slowly and in pulses, like it starts and stops a few times per second while moving. I've...
View Article