How to Increase the maximum temperature setting in Marlin (1 reply)
Hi, I’m using SKR mini e3 v3 board and Marlin 2.1.x bugfix version. I want to increase the maximum temperature to 395. So I corrected lines 651 and 652 in the configuration.h file to 395, and the...
View ArticleMarlin and endstop setting (1 reply)
Hello, I am compiling Marlin 2.1.2.2 for a BTT SKR_3EZ with TMC2209 steppers. I have set up sensorless homing; Trinamically for the X & Y Using a BL Touch sensor in the dedicated slots for the Z...
View ArticleHotend stops heating at around 40 degree celcius (1 reply)
Hi, I'm trying to create a simple setup with an extruder, a hotend and a fan (all components of the Prusa MK3S) using RAMPS 1.4 and the Marlin software. Unfortunately, the attempt to set a temperature...
View ArticleLCD connected to Mini Rambo 1.3 Running Marlin Started Showing Only Bars (no...
I'm trying to upgrade the control board in an UP Mini 2 to a Mini Rambo 1.3a board, and initially, when I connected the screen and flashed the Marlin firmware the LCD screen was working as expected....
View ArticleAnyone successfully get PWM laser support for STM32 going? (1 reply)
I have a target platform using an STM32F407 that I'm working on getting laser (with PWM) going, but before I start chasing issues too deep into the firmware I thought I'd check to see if anyone has...
View ArticleAssigning pins for custom buttons, What Have I missed? (1 reply)
Good afternoon everyone. I am running a BTT SKR_3_EZ for my controller. My printer has 1 extruder. I am trying to set up an Orbiter filament sensor. I have the runout part of the sensor working well....
View ArticleHoming, Offset, Probe, USB Etc, Etc Nothing works right! (1 reply)
Marlin problems I have an Ender 3 v2 Installed Sprite Extruder Pro Kit Installed Cr Touch BIGTREETECH SKR V1.4 Turbo Control Board TFT35 V3.0.1 Touch Screen Display TMC2209 V1.3 Stepper Motor Driver -...
View ArticleControlling both extruders independently on an IDEX printer (no replies)
I have a BCN3D EPSILON W27 and for a project I want to simultaneously control both extruders independently, for example I want T0 to move 10mm while T1 moves -15mm. From what I can understand the M605...
View ArticleI Need Help Setting Z Offset (no replies)
I have an Ender 3 v2 Installed Sprite Extruder Pro Kit Installed Cr Touch BIGTREETECH SKR V1.4 Turbo Control Board TFT35 V3.0.1 Touch Screen Display TMC2209 V1.3 Stepper Motor Driver - Settings for...
View ArticleWrong Z height after long print, Z-shifting (1 reply)
Hello, dear plastic-melting community I few months ago, I replaced the old electronics of my printer with a BIGTREETECH Manta M8P with Raspberry Pi 4. Firmware: Marlin 2.1.2.1 / Marling 2.1.x (bugfix...
View Article:S Z_CLEARANCE_DEPLOY_PROBE is being ignored during Home All (no replies)
Hello. After finishing the entire configuration of the MKS MONSTER8 V2 board in Marlin 2.0 from Configuration.h / Configuration.adv, I noticed that Z_CLEARANCE_DEPLOY_PROBE is being ignored during...
View ArticleEnable Serial Port 3 SKR 1.3 Marlin 2.1.2.2 (no replies)
I would like to configure Marlin to use UART3 on the default pins 0.0 and 0.1. Those pins go to E1 Step and E1 DIR which I am not using. When enabled in configuration.h and compiled I don't get any...
View ArticleLCD hotplugging (no replies)
I am building a printer where there's really no good place to stick an LCD screen. I planned to have no LCD at all, and just use Marlin's "auto-print" feature, where you insert an SD card and reboot...
View ArticleX motor will not bump after hitting Xmin endstop or move in positive...
Hi I am building a CNC machine and use the latest Marlin software (2.1.2.4) for the firmware to control the X, Y and Z axis and endstop behaviour. When I adjusted Marlin I set the number of extrudes...
View ArticleY axis randomly goes to wrong direction (no replies)
Hello I have a 3d printer based on MKS ROBIN NANO v1.2 with TFT35 touch screen. I install the marlin firmware v2.1.2.4 and after that its hard to have a correct printing (1 in 4 or 5 attempts). What i...
View Article:S Marlin Code ändern (custom Printer) (4 replies)
Hello everyone, This is my first message on here. I am repairing a Rep Rap printer from 2013. I have attached a few pictures of it. I know quite a bit about hotend endstops and other "mechanical"...
View ArticleRemapping Pins for Non-printer (no replies)
I'm having some issues with figuring out how to remap a pin and could use some help. I'm putting together a 3D scanner that is based off of this system ( [github.com] ) I've had to make a lot of...
View ArticleTrying to add a GD32F303 board in Marlin (2 replies)
Hi All, Hopefully this is the right place to ask this? If not, if someone could point me in a good direction, that would be appreciated! I am trying to create a custom Marlin install for a new...
View ArticleThermistor NTC3950 (no replies)
Hello i buy an extruder like e3dv6 from amazon and come with a NTC 3950 Thermistor. In marlin 2.x i've setup type 1 for the thermistor but it doesn't to work well, could you suggest me another...
View ArticleClik here to view.
Full Graphic Smart Controller - Blank Screen (4 replies)
Hi all! I've got a Ramps 1.4 with a RepRap Discount - Full Graphic Smart Controller - 12864. The problem is that the display board is working, I can see from serial output that sd card is detected,...
View Article