Marlin 1.1.9 and Ramps 1.6 (1 reply)
Hi, Thanks for letting me join the group. I want to use a Ramps 1.6 board when I build my second printer, question is Marlin only seems to list Ramps 1.4 board in the boards tab, can I still use the...
View ArticleWhich file is the root file? (no replies)
I know this my sound silly to people that know exactly how to program in C++ and for the Arduino but, which file is the head vampire so to speak? I'm guessing Marlin_main.cpp right? I'm starting to...
View ArticleIs P.I.N.D.A 2 support built into Marlin at this point (no replies)
Does anyone know if the temperature compensating P.I.N.D.A. 2 probe is supported in 1.1.9 and/or 2.x Marlin? Or is that only a feature that is available in the Prusa version of the Marlin firmware? I...
View ArticlePiezo20 merlin A8 configuration. (no replies)
Hi Got marlin 1.1.8 and anet A8 (stock mainboard) Tatara. Today i got my piezo20 with printed parts but don't know how to "implement" them to marlin for A8. Anyone got working marlin on A8 with...
View ArticleNeed help: static_assert(LEFT_PROBE_BED_POSITION >= MIN_PROBE_X,...
Hello everybody, I was using the marlin 1.1.8 with some changes in Conditionals_post.h. Lines 1009-1012: #define _MESH_MIN_X (max(X_MIN_BED + MESH_INSET, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))...
View ArticleZ axis buzzing (stalling?) (2 replies)
Hi all, I have a problem that I think is firmware, but I have run out of ideas. I've had a CTC Cartesian with a Geeetech GT2560 Rev A board for a couple of years which I have updated slowly over time,...
View ArticleAutobedleveling X and Y axes stops to soon (no replies)
Hi, after updating my Prusa i3 to marlin 1.1.9 i have got problems with the autobedleveling function. Everything else works fine but if i start a printjob and the autobedleveling (ABL) starts and want...
View ArticlePronterface won't connect to RAMPS 1.4 (2 replies)
I have been having trouble getting Pronterface to connect to my RAMPS 1.4/Arduino Mega. When I try to connect, the monitor just says "connecting...", and when I unplug my board, I get the following...
View ArticleMarlin 1.1.9 Full Reprap Graphic not showing correctly (no replies)
I'm trying to port over my settings from 1.1.8 to 1.1.9 for my JGAurora Z603s. I've got everything working apart from a glitchy LCD. I've compared source code for about 3 hours but not getting...
View Article(solved, my head was the problem=) ) Probe z Offsett has no effect on marlin...
Hi, I upgraded to Marlin 1.1.9 and finally configured my cap sensor for abl. I have read trough numerous posts without luck. When i put in the probe z offset either trough octoprint Marlin eeprom...
View ArticleCan't connect USB with Marlin 2.0 on MksSbase (no replies)
Hello, I compiled and install Marlin-bugfix2.0.0 on a MKS SBASE board. After some setting in config, it runs OK with my Reprapdiscount Full graphic smart controller. Great, thanks ! But, connection...
View ArticleAnyone get skew correction to compile (1 reply)
Marlin 1.1.9 with Folgertech i3 2020 I'm trying to understand how to implement skew correction. If I understand the comments in configuration.h I can either enter my measurements for XY_DIAG_AC, etc...
View ArticlePINS.h not working correctly ??? (no replies)
I build a Ultimaker clone. (C-260 ) . Its working. Based on MKS Gen L v.1.0 board Want to print high temperature, so changed the head . Added PT100, amplifying board. HW is working till the last PIN....
View ArticleSD card (2 replies)
Hello. I have a new Einsy RAMBo 1.0a motherboard and I configure Marlin v1.1.9 firmware on this board. I have a full graphic smart controller LCD. After changing configuration.h, I managed to set up...
View ArticleHow to use PHOTOGRAPH_PIN (M240) to take a picture (no replies)
Hello, I have looked around, but I cannot seem to find any info about how to use the M240 command to take a picture. I am just barely switching to Marlin 1.1.9 on my good ol' RAMPS 1.4 Chinese clone....
View ArticleMarlin 1.1.9 major bugfix problem (no replies)
Hello everybody, I was using the marlin 1.1.8 with some changes in Conditionals_post.h. Lines 1009-1012: #define _MESH_MIN_X (max(X_MIN_BED + MESH_INSET, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))...
View ArticleHow to add extra movement in Y axis just before Z homing (no replies)
Hi I got one DaVinci 1.0 converted now with mks board and e3dv6 with direct extruder but pancake motor that hotend carriage didn't have enough torque so i mount stock davinci motors for direct...
View ArticleFirst layer squishing (no replies)
Hey guys, I'm having trouble with my first print/part. I'm not sure what this issue is, but I believe it to be either tinkercad, or how I'm slicing in cura. I have a test object, and a bedleveling...
View Articlehelp needed to run only one Z stepper (and two E steppers) (no replies)
Hello I have a MKS Gen-2Z V1.1 board and I have the newest version of Marlin (1.1.x) 1) when I move the Z-axis both stepper motors turn, but I only want to use one of them for Z and the other for E1...
View ArticleQuestion on UBL and Fade Height (no replies)
I've been using UBL for a long time now and I'm on the Marlin 1.1 bugfix branch. In my configuration.h file, I have ENABLE_LEVELING_FADE_HEIGHT defined. The default fade height is 10 mm. So once the Z...
View Article