M122 returns wrong driver information (1 reply)
Hi, I´m using Marlin 1.1.9 on a ramps 1.4 with 5 TMC2208 drivers (connected with serial Y cable). E1 is used as Z1 for the second Z stepper. Basically everything works fine, but it seems that M122...
View ArticleDual Y axis machine endstop problem (no replies)
Hello. I am having a homing problem with a custom machine. It has 2 motors on the Y axis, and separate endstops for each motor, connected to the Y_MIN and Y_MAX slots. If I have Y_HOME_DIR = -1...
View ArticleAuto Home M1.1.9 How to change reaction to get a bit back (no replies)
Hello In the previous version of the Merlin there was a solution that I liked very much: after G28 each of the axis was coming back a bit. In my current version it isn't. Is there a chance to change...
View ArticleFYSETC F6 v1.3 Marling 1.1.9 TMC2130 M122 not working (no replies)
Hi All, first time on the forum. Been plating with the FYSETC F6, loaded Marlin on it, looks like like it's working, but there are some issues. I tried running M503 command and it fails: SENT: M503...
View ArticleMarlin 2.0 with 12864WZ-10 LCD? (no replies)
Hi all, Any insight into getting the 12864 LCD working with Marlin 2.0? I'm running this on the FYSETC F6 1.3 board... Marlin 1.1.9 seems to work correctly for this LCD. Thanks! JM
View ArticleCase Fan MKS Gen L (no replies)
I am new to this forum. So please forgive my inexperience. I would like my case fan to be attached to the location marked in yellow. It is a 12/24v spot. I am up for other locations as well. However....
View ArticleMarlin 1.1.9, TMC2130 V1.1, no movement (7 replies)
Hi, after fighting a 32-bit Chinese controller for a year it finally decided to even blow some mosfets, so I now upgrade my printer to a simple RAMPS 1.4 on 24V with TMC2130 V1.1 drivers. Should be...
View ArticleMarlin and Anet LCD12864 Installation Confusion (no replies)
Hello all. Here's my senario: I am using an Arduino Mega 2560 and a Ramps 1.4 for a newly built 3D printer. The control board I am using is an Anet LCD12864. I tried just un-commenting it in the...
View ArticleOdd Z-Probe Issue (1 reply)
So I'm currently trying to set up my z-probe for my printer. When I upload my firmware my z-probe works as expected. It triggers when the bed is close and the light is on but shows as open when the...
View ArticleZ home pronterface works, G28 Z0 makes Z movement freeze (no replies)
Hi, with a lot of help on this forum and some tinkering I got my RAMPS 1.4 (24V) with TMC2130 V1.1 stepper drivers and Marlin 1.1.9 working. As sensors work, all axis and the extruder move as they...
View ArticleExtruder direction voltage question (no replies)
I'm running an Arduino Mega 2560 with a RAMPS 1.4 board. We have installed the 1.1.X Marlin firmware. I have a question about modifying the idle direction voltage for our extruder. Our project is a...
View ArticleAuto Bed Leveling issues (4 replies)
[attachment 108583 AutoBedLeveling.png]Dear Gentlemen, I would like your help to see if we can solve the following issue. Here it goes: I built a t-slot 3d printer using the Ultimaker type as a...
View ArticleRepRap Full Graphic Controller SD Card Issue (no replies)
I have spent a long time trying to get SD card support working on a Full Graphic Display and RAMPS. I have tried 2 Megas, 2 RAMPS, 2 displays and 5 SD cards (All formatted multiple times). Neither of...
View ArticleSet Z=5mm after homing G28 (1 reply)
How to set , in Marlin, X=0 Y=0 and Z=5mm after G28 homing? The raison is :to protecting my flex magnetique printbed by warming up , preventing the nozzle touching or to close the bed .
View ArticlePrusa i3 Stuck on E1 Heating... (no replies)
Hi, I just finished assembling a RepRap Guru Prusa i3 printer and am using Repetier-Host Mac 1.1.0 along with RepRapGuru_Marlin_v4 on Arduino 1.8.7. When I tried running it the first time, the LCD...
View ArticleGcode help needed (no replies)
Hello All! I have an Anycubic i3 Mega and to make the bed cool faster I installed a fan to cool that when printing finished. It's the "end" gcode: M117 Printjob done! M104 S0 ; turn off extruder G1 X0...
View ArticleFilament purge speed (no replies)
Ultimaker2 has a autofeeder to load filament tru the tube ad fast speed, slows down before entering the nozzle. Now can this be done by Marlin for my bowden setup? I have bondtech extruder and when I...
View ArticleTrouble configuring 3d touch z probe (5 replies)
G'day everyone, first of all great forums, lots of good information around here. Plenty of which has come in handy in the past. Im having some trouble trying to setup my new z probe. I have purchased...
View ArticleTrouble configuring MKS SBase bugfix-2.0-3.x Auto level (no replies)
Hi, I would like to ask for help, because I'm in trouble with configuring Auto level with my custom build delta printer with inductive probe, which works. I adjusted DELTA_ENDSTOP_ADJ and I want to...
View ArticleBLTouch and UBL (no replies)
Hello, I'm having real troubles getting my BLTouch and unified bed levelling working and was wondering if someone could critique my calibration setup. I use this every time anything physically changes...
View Article