Compile error (1 reply)
Brawling with Marlin. The printer is an old CTC Replicator Dual and the new board is a MKS Gen L and and define in Marlin as per Boards.h I finally got the board wired up and the drivers tuned. After...
View ArticleTemperatures of bed and hot end being set to 0 during run? (no replies)
while using marlin 1.1.8 I get now and again something setting the bed and hot end to zero this is not detected by the printer, has anybody else had this problem or is there ayway to detect this while...
View ArticleWierd Stuff after upgrade (no replies)
Ok so i updated from Marlin 1.0.1 to 1.1.9 Problems so far 1. Axis all seem inverted when i move them manually 2. When i home X it go the right direction for like 1mm then drops z like 5mm 3. My bed...
View ArticleBLtouch/Ender 3/Marlin 1.1.9 (Not working) (no replies)
Hello, I just got done upgrading my Ender 3 Pro with a genuine Antlabs Bltouch Smart v2.0 following this guide [www.youtube.com]. In short I used a Pin 27 board to avoid having to splice anything onto...
View ArticleLinear Advance help (1 reply)
Hi, Just for knowledge; I'm wondering how does linear advance work in the backend? What does it actually does to make the extruder axis linear as similar to other axes. Would be great if you could...
View ArticleIssue with Marlin and reprap display (3 replies)
I have the graphic 128x64 display and whenever I try to verify before uploading I keep getting this message saying "#error "Please select no more than one LCD controller option." What is this as I...
View Articlehome no longer goes to center of bed and z safe homing now creates error (no...
After Updating my marlin to bugfix 2.0 My Cube no longer homes to the center of the bed.I had all the pertinent setting that I have tweaked for my machine saved so I only changed those settings. I...
View ArticleHow Do I Enable the M140 Heating Bed Option? (no replies)
I am using Marlin 1.1.9. I am trying to heat my bad using the 'M140 S60' command but it's not working. When I enter this in Pronterface I get: Setting bed temperature to 60.000000 degrees Celsius....
View ArticleMarlin G38.2 dont move Z (no replies)
Good Evening and nice Christmas :), i have a question. I have a CNC Mill running with Marlin and OctoPrint over Raspbian. Everything is working fine but i did get the G38 command not working. The...
View ArticleBLTouch - Marlin 1.0.0 RC2 (no replies)
Hi all, I've been looking for help on this for a while and haven't gotten anywhere with it (including other posts in the wrong location on this forum). I have a Leapfrog Creatr (original) with their...
View Article3 problems with Marlin 1.1.9 and MKS GEN 1.4 (no replies)
OK, the first problem is when trying to compile Marlin with the Auto bed levelling. I get the following error: expected ',' before numeric constant #if ENABLED(AUTO_BED_LEVELING_LINEAR) ||...
View ArticleThermistor/temperature problem (2 replies)
hi everyone, i am new on this forum and having an anet a8 since a while. I am trying desperately to install Marlin (1.1.9) but there is an issue with the thermistors behavior. By the way it is working...
View ArticleMarlin 1.1.x Axis configuration issues (no replies)
Hello all, New to this forum so please be patient. I inherited a Solidoodle Workbench which was working when I received it. The factory controller board died and the company is no longer in business....
View ArticleMarlin 2.0 Low Memory Warning (1 reply)
Hi All, I am configuring Marlin for my 3D printer and I have run into a warning: Sketch uses 207664 bytes (81%) of program storage space. Maximum is 253952 bytes. Global variables use 7779 bytes (94%)...
View ArticleNeed to define Y_CS_PIN in Configuration_adv.h (1 reply)
Sorry to be a pain in the butt but when I try to compile Marlin 1.1.9 I'm getting the following error ( #error "Y_CS_PIN is required for TMC2130. Define Y_CS_PIN in Configuration_adv.h."). How do you...
View ArticleMarlin 1.1.8 - MKS Gen 1.4 and TMC 2100 (1 reply)
Hello, I've searched through the forum and can't find anyone who's running into the same issue as me. I've just finished building a CoreXY. Initially, I had an MKS Gen 1.4 with DRV8825's throughout. I...
View ArticleArduino IDE search all of sketch (no replies)
I have been working with Marlin 1.1.7-1.1.9 for a few months. I am looking into 2.0.x and find that only 3 files are shown in the IDE now. That means that search does not go across all the source...
View ArticleProblem enabling Z Home Safe (no replies)
Does anyone know why I'm getting this error (static assertion failed: Z_SAFE_HOMING_X_POINT is outside the probe region.) when I try to enable Z_HOME_SAFE feature. I'm using Marlin 1.1.9 and an MKS...
View ArticleError compiling for board (1 reply)
Hi, I am new to Marlin and just finished setting up the configuration file, but whenever I try to compile the code I get the following error...
View ArticleBL Touch on KFB-board with marlin 1.18 on Anet A8M (2 replies)
I have a problem. I flashed my Anet to version 1.18 with "all" the BL-Touch changes. On start up the BL retract 2 times en stays the pin is in the high position If I do G28 Z the machine never stops....
View Article