Z axis disables when printing second part (no replies)
I have an issue after changing the lead screw. It prints great until it comes to the second part. The first part it prints well (set up in cura as one at a time). However, when the second part prints,...
View ArticleCR10-S5 , + Marlin - random stop during G28 home. (2 replies)
CR10S was worked fine. (Marlin 1.1.9 from master) Added 1m original cable extension. - connectors and termination looks good. - signals verified with multimeter, - (no off behavior when touching...
View ArticleProblems compiling Marlin for Anet A6 (2 replies)
I am trying to compile Marlin 1.1.9 for the Anet A6 using the Arduino IDE and am having multiple errors. I put a hardware definition for the Anet in the Arduino/hardware directory, added a zip library...
View ArticleX and Y Homing issues (1 reply)
I get a "error: printer halted. (kill() called!" Any time I home my machine with X or Y axis. I have just installed a 3D touch auto bed level sensor, ironically it works fine. I was using Sprinter...
View ArticleClik here to view.
Marlin 2.0 MKS SBase 1.3; set driver current (no replies)
Hi, I would like to know how and where the current settings for the DRV8825 drivers are defined. I cannot find a default setting anywhere, I can find this on the configuration_adv.h. page but I cannot...
View ArticleCan anyone add MMU 2.0 to his printer ? :S (2 replies)
Hi guys, Am very interested in the MMU 2.0 and willing to buy the kit soon. Only that I heard Josef Prusa saying that the kit is only compatible with Einsy board and Prusa i3 MK versions. Honestly I...
View ArticlePrinter Response (1 reply)
Hi, I have an ANET A8 3D Printer running Marlin 1.1.x. I'm using a Raspberry Pi to use serial communication for the 3D Printer for my school project. I was able to send GCodes properly to the 3D...
View ArticleFour Point Bed Level & Twist on 1.1.9? (no replies)
Hi, Can anyone point me toward a guide for setting up a four point bed level correction in the firmware? Thanks.
View ArticleRe-ARM UART pins for TMC2208 (2 replies)
Hello all, Am trying to figure out how I can get UART to work on my Re-ARM and get it to control the 4x TMC2208 stepper drivers I need. Apparently the Re-ARM doesn't break out these pins, so I can't...
View ArticleMarlin bugfix 2.0 and TMC2130 error on compiling (no replies)
I've got four TMC2130 drivers on my board, all configured as standalone except for the Z one, which I configured (solder pads and bridges) and wired to be used with SPI. This is new for me, I wanted...
View ArticleSmoothie to Marlin (1 reply)
Hello, Someone know how move Smothie Firmware to Marlin Firmare? Is it possible to do?
View ArticleTMC2100 crashes with LIN_ADVANCE (no replies)
So I have an Anycubic delta with Trigorilla board (REPRAP 1.4). I have configured anf flashed latest Marlin bugfix-2.0 (8 Jan 2019). All seems to be working fine. I then enabled LIN_ADVANCE and...
View ArticleProblems with stepper drivers (2 replies)
I bought 4 pcs stepper drivers HY-DIV268N-5A.I've connected them to a controller MKS Gen v1.4 and I use the firmware Marlin 1.1.4. I power them with 12V/360W power supplay. I've printed a test...
View Articleautobed level z probing issue (no replies)
I finally got marlin working on my ramps 1.4 board correctly. My only issue now is G29 auto bed level dosnt work correctly. After homing If I use the G29 command to start the auto bed level, it will...
View ArticleZ motors malfunction (1 reply)
Hi, So I just installed a new RAMBo board on my Mendelmax 3 and flashed it with Marlin firmware. The first thing i attempted when connecting it to the software was testing all the motors. The X and Y...
View ArticleTemperature Instability (no replies)
After installing a genuine e3d v6 Gold on my printer I am having temperature instability. I change the thermistor to 5 in the firmware, and have run PID tuning. It is so bad that it will occasionally...
View Article[solved] Commands over Serial not working "unknown command:" (8 replies)
Hallo, i hope im in the right place here. I have an upgraded Anet A8 with ramps1.4. I wanted to upgrade to TMC2130 and wired them for spi. Upload new config -> power on -> stepper wont move. I...
View ArticleClik here to view.
Adjusting Kinematics of Marlin (no replies)
I am trying to get the kinematics to work for a printer i built. I used the MarkForged kinematics as a model for mine. If you are not familiar, I provided a picture below of what that looks like. My...
View ArticleUsb reset (no replies)
I am switching my printer over to Marlin firmware from Repetier. After uploading I have noticed that anytime I connect to it through usb it restarts my printer. This never happen with Repitier. Is...
View ArticleUnable to implement fast/slow probing on 1.1.9 (no replies)
Hello everyone, I have an i3 clone with a RAMPS 1.4/2560 combo running Marlin. I've been humming along running 1.1.8 for some time, and decided to reflash to 1.1.9 to test out the new linear advance...
View Article