Kill motion on endstop hit (2 replies)
Hi, I just don't get it... Why isn't the default behavior such that when hitting an endstop during printing, printing is *immediately* halted? I think it should be a basic safety precaution. I...
View ArticleZ probe dosnt stop when Z is homed (no replies)
Pretty much as the title states, I see videos of others using their Z probes online and mine does not act the same way. auto level cant be done unless I home each axis to 0. The issue is the Z Probe...
View ArticleFOLGERTECH 2020 upgrade Control failure (no replies)
I recently upgraded all three axes of my 2020, added a 3D touch, and uploaded 1.1.9, then tried 1.1.9 bugfix from 01/18/2019. I use RAMPS 1.4, and OCTOPI on a Rasbpi 3. The printer homes, heats and...
View ArticleStrange XY behavior after adding bed leveling (no replies)
I added a BLtouch clone probe to my CR-10 printer running Marlin 1.1.9 and now I have some issues after bed leveling. After my G29 bed leveling command finishes, my printer head won't move on the Y...
View ArticleMarlin bltouch (no replies)
Hey all noobie here so I recenlty started on this bltouch journey and im almost there i have an issue while starting a print ,the probe is fine it homes great but when the print starts it just blobs...
View ArticleMesh Bed Levelling (no replies)
Hello everybody! I am using manual Mesh Bed Levelling for my Tronxy X5S and my I3 Mega which works OK. I have a question though. The various Z offsets that are collected are added/subtracted from the...
View ArticleManual Bed leveling with a probe (no replies)
I have currently updated to version Marlin 1.9 on my CR-10s. I have enabled manual mesh bed leveling and it works well. So now I was wondering can I use manual mesh bed leveling with dial indicator to...
View ArticleZ axis wont lower (no replies)
Hi, So out of no where are started getting this "HARDWARE ERROR". I was printing yesterday now today i get an error every time it tries to home the axis' . It will do the x and y but when it comes to...
View ArticleBLTOUCH + DUAL Z ENDSTOPS (no replies)
Hello! I am already using dual Z motors with seperate drivers and individual Z endstops for my Tronxy X5S. One Z endstop connected to Zmin and the other to Zmax. Also I have enabled manual mesh...
View ArticleTMC2130 and Marlin 1.1.9 (6 replies)
Hello, I want to use x2 TMC2130 driver (on the X and Y axis) on SPI mode using Marlin 1.1.9. However I am not able to compile the code and I constantly get this error: In file included from...
View ArticleMarlin dual extruders, dual heaters setup help on MKS GEN 1.4 (no replies)
Hello everyone, after printing parts in the last 2 -3 weeks with the single nozzle setup, I wanted to upgrade to a dual nozzle, I really want to use PVA filament ofr the support, so I don;t need to...
View ArticleX axis end stop not stopping. (no replies)
Hi. I have just built a Anet a8-m dual printer. The x axis end stop was working with the original software. I have changed to Marlin and used a configuration I found for the KFB 2.0 control board. Now...
View ArticleHow to permanently move PART COOLING FAN to pin 6 (MKS GE 1.4 second servo...
Hello everyone, I want to move the PART COOLING FAN to pin D6, and use an H-BRIDGE L9110S module to power the fan, I want this also when I configured Marlin with a single EXTRUDER, because I wired...
View ArticleZ-axis "Home" problem (1 reply)
Hi everybody! I am new to the 3d printing world and I recently bhought the Flsun i3 plus(with autoleveling) and I already made many succesful prints with the single extruder. The firmware I used was...
View ArticleMarlin upgrade and wrong coordinates (1 reply)
I am trying to complete an upgrade on my Marlin firmware and I'm really struggling with getting all the movements and coordinates set up correctly. I've gotten to the point where everything moves in...
View ArticleFilament change only purges (no replies)
Hello, today I decided to activate filament change on my printer running Marlin 1.1.9 on an Anet board. But now after flashing it, I can't get it to work as it should. What happens is that when I...
View ArticleUSE_CONTROLLER_FAN with hardware PWM fan (no replies)
I've come across something weird and wanted to make sure I'm not doing anything stupid before adding an issue on Github. I'm using an MKS Gen 1.4 board flashed with Marlin-bugfix-2.0. I'm trying to...
View ArticleFilament run out sensor - disable. Marlin 2.0 (no replies)
Hi All, I have been using a filament run out sensor for a while and it has been useful. When I print with flexible filament though I would like to disable it and send the filament directly to the hot...
View ArticleProblem Sd card extended cable (no replies)
Goodmorning everyone! I decided to build my first 3D printer. I bought a 12864 Full Graphic Smart Controller LCD and an sd card extension. I have the following problem: I insert the sd card inside the...
View ArticleCold Start Goes wrong Direction (no replies)
Help. I have a very strange repeatable problem. I'm running Marlin 2.0 on a Cohesion 3d Remix board (LPC1769) with all A4988 drivers. It works almost flawlessly and I'm really liking it but... when I...
View Article