Marlin 2.bf - G76 - Probe temp. compensation error (no replies)
Hey there, I just dug out my Wanhao Duplicator I3 and did a few upgrades including SKR 1.4, TMC 2130 SPI and an inductive Z-probe. It auto levels and prints fine but now I wanted to add temperature...
View ArticleX/Z axis proximity endstop help (no replies)
Hi guys, I’ll explain the situation before my issue. At work we had a ormerod 1 with duet card, this had a proximity sensor for both Z and Y endstop position. It been in a box in bits and I was asked...
View ArticlePIDTEMP Errors, "DEFAULT_K*" not defined (no replies)
I'm running Marlin 2.0.x and when compiling I get errors for the PIDTEMP area of the code. It's in Configuration_Store.cpp and lines 2621,2622,2623 it calls out for DEFAULT_Kp and Ki and Kd but says...
View ArticleMarlin PID Autotune (1 reply)
I've been using Marlin 1.1.8 for quite a while, after 'converting' the original firmware supplied with my printer to the 'official' Marlin, and it's been working great. I tried upgrading to 1.1.9 but...
View ArticleSend nozzle to center of print bed ? (1 reply)
After doing a homing procedure is the anyway to send the nozzle to park in the center of the printbed ? I used pronterface to do this but is there any way to configure Marlin to do this without...
View ArticleRegular Pimples on the printing Surface (no replies)
Hello Guys, I have some Problems with regular pimpels on my surface as you can see on the picture. G-Code is also enclosed [attachment 114677 WhatsAppImage2020-02-29at12.56.13.jpeg] Hard/Software: -...
View ArticleSetting temps beyond the thermistor table. (3 replies)
I haven't used Marlin in ages, and never had cause to push high temps when I did, but the question came up recently.. How does Marlin handle it when an operator sets the nozzle temperature higher than...
View ArticleMarlin homing issue (no replies)
I've been running Marlin 1.1.8 for a long time, since I got the CBot version of Marlin and copied the values over to the official Marlin 1.1.8. Marlin 1.1.8 has been rock solid for me, so I tried...
View ArticleMarlin crashing every time print ends (no replies)
Summary on issue: Every time print finishes, printers software crashes in various ways: - with bomb-like ticking sound which is contineud by continous beep. (most common) - simply by getting stuck on...
View ArticleI2C control of pcf8574 (no replies)
I am using a BTT SKR 1.4 Turbo board which has limited additional I/O pins and i would like to use an I2C expander based on the pcf8574 chip to control basic on / off functions. I have the board...
View ArticleZ axis wont' register correctly in marlin (no replies)
Hi I'm using marlin 1.19+bugfix and trying to set the steps/mm on my axis. I have succeeded in setting the X.Y axis correctly but I can't define the movement of the Z axis. When I make 10mm move the...
View ArticleDelta setup (no replies)
Hello, Apologies in advance for this post, I feel sure that this has been covered many times but I cannot find an answer. I have at last finished building my Delta, configured Marlin 2 to run it and...
View ArticleKR-PRO-V1.1 board not converting firmware.bin to FIRMWARE.cur (no replies)
Hi, Any ideas why my SKR-PRO-V1.1 board not converting firmware.bin to FIRMWARE.cur and usb cable do not respond with PC. In the past everything was fine. Also tried to use other SDcard with FAT32...
View ArticleMendel / i3 DIY sulking. - probing problem (no replies)
Hi, I'm not sure if this is the place for this problem as I'm not sure if it is a hardware or firmware one. I must admit that my self build printer is sulking, it used to print very well but no...
View ArticleError when compiling Marlin 2.0 (no replies)
Hi all! I have an Creality CR-10 that is modified and now I want to get it running with a Bigtreetech V3 controller board. I have followed the instructions on the Marlin site and gone with the...
View ArticleMarlin 2, i3 Pro B, Z clearance being ignored (no replies)
So I have a Geeetech i3Pro B, currently running Marlin 2.0.4.4, and I bought a 3DTouch (BLTouch ripoff?) but I've been having nothing but trouble getting it working. I think I'm more or less there...
View ArticleGeeeteck I3 Pro C running Marlin 2.x ?? (no replies)
Does anyone have a better starting point than the example config for this printer ??? The config in "\config\examples\Geeetech\Prusa i3 Pro C" compiles OK but has several problems (On "auto home" it...
View ArticleMarlin Homing problem. (no replies)
Setting up my modified FolgerTec I3 with a SKR v1.3 and Marlin 2.0. Working through everything in steps and learning. Got homing and bed leveling working, but ran into a problem with the extruder fan...
View ArticleCompiling Marlin 2.0.x horribly slow under Arduino IDE 1.8.12 (1 reply)
It seems 5-10 times slower than compiling 1.1.8 !!! I realize it's more complex but even so ... Dave
View ArticleG34 Issues... Large format machine (1 reply)
I have been working on a large format printer with 3 Z steppers. // The size of the print bed #define X_BED_SIZE 610 #define Y_BED_SIZE 425 // Travel limits (mm) after homing, corresponding to endstop...
View Article