LCD12864 Ramps Plus/MELZI display and RAMPS 1.4 pin assignment (no replies)
Hi. I decided to change my 3d printer board (melzi v2.0.1 with Marlin v1.0) to atmega 2560. I will use LCD from old system. Because lcd connected to the melzi board directly, there is no lcd adapter...
View ArticleMarlin 2.0.X : error sketch\src\module\temperature.cpp (no replies)
Good morning all, My compilation seems to finish correctly, but I have the following error in the traces : Error while detecting libraries included by...
View ArticleUpload problem (2 replies)
When I start uploading, after a while, I get the following error with arduino 1.8.12 : "C:\\Program Files (x86)\\Arduino\\hardware\\tools\\avr/bin/avr-size" -A...
View Articlemarlin2 with tmc2209 xy sensorless homing z endstop but start printing 2mm...
HI Guys, i am setting up a folger ft6 and i have it setup with tmc2209. i have configured the sensorless homing on x and y and Z has endstop. the printer homes ok on xyz but when printing it lower the...
View Articlemarlin delta printer acting like it had a stroke (no replies)
fairly recently upgraded to marlin 2.0(bf) on my scratch built delta printer, had some problems with calibration but eventually got it running and was making some decent prints. I was looking forward...
View ArticleEffector crashes into X tower after Delta Calibration (no replies)
I recently rebuilt my printer with a new Board, new stepper drivers and new Firmware. Now, when I go to do Delta calibration to set up printer for first time, calibration fails by crashing into X...
View ArticleMarlin 2.0 compille problems for a custom controller board (2 replies)
Hi everybody. I have a problem with Marlin 2.0 in PlatformIO. I try to compile it for a STM32F103RET on a custom build board (the pinout is similar to the bigtree skr mini v1.1, but one pin is...
View ArticleCan't set BLTouch probe offset in Marlin TH3D V1.R2.10d (2 replies)
Can't set BLTouch probe offset in Marlin TH3D V1.R2.10d When I go into Control -> motion -> probe z offset the maximum negative value I'm allowed to input is -4.975 but this still leave the...
View ArticleMarlin 2.0 - Enable Serial3 port (1 reply)
Greetings! I want to enable Serial3 port in Marlin 2.0 firmware with different baudrate than Serial0. I see that Marlin disables standard HWserial and configures the communication with its own...
View Articlea display for the MKS SBASE (no replies)
This is my issue. I have an MKS SBASE 1.3v and a MKS TFT3.2 display. I also have a old LCD reprap discount smart controller off the printer I’m re-building. Anyhow I have loaded both Soothieware and...
View Articleheated chamber (no replies)
Hi, I'm building a very large printer for ABS and NYLON that needs an actively heated enclosure, I'm using Marlin so I can drive separate stepper driver modules for bigger motors, I'm in the middle of...
View ArticleWeird position after homing with marlin 2.0 (no replies)
Hi, I've been upgrading my RAMPS1.4 to an SKR V1.4 and flashed marlin2.0 on it. Configured it and was pretty content that everything still worked. Then I executed G28 Z0 and my printer did its homing...
View ArticleClik here to view.
Junction Deviation or Linear Advance? (no replies)
I've been working on trying to start using some of the latest features in Marlin. A few weeks ago, I implemented Junction Deviation and thought I had a pretty good value of .03 with an acceleration of...
View ArticleMarlin 2.0.5.3 - Z_DUAL_STEPPER_DRIVERS (no replies)
Hello, Could you tell me what has become of # define Z_DUAL_STEPPER_DRIVERS in Marlin 2.0.5.3? This option is no available in configuration_adv.h :( . I have a SKR 1.4 motherboard that I would like to...
View ArticleY moves when only X is comanded (no replies)
Hi guys, I have a printer that I've modified to a different type of printing for my school work (basically I'm just using the movement part of Marlin), but i'm having an issue. See the Gcode sample...
View Article"Unload more" in change filament menu (no replies)
Hi guys. When changing filament, there are two options: Purge more and Continue. I need a third option, "Unload filament", because in my printer sometimes the filament goes the wrong way (long...
View ArticleError meaning (4 replies)
when I compile a new version of Marlin 2.0.x bugfix I get this error multiple times, maybe on all the .CPP files. Error while detecting libraries included by C:\Users.............. The compile does...
View ArticleMKS SBASE 1.3 Marlin 2.0 RRDSC SD Card not work (no replies)
I have problem with Marlin 2.0 MKS Sbase V1.3 + RRDSC 12064. The LCD menu works, the SD card does not work. SD cable is: P0.8 to J8-3 P0.7 to J8-2 P0.9 to J8-4 (P0.5 to J8 -4) P0.27 to J8-5 What...
View ArticleUBL mesh probing fails after first point, Marlin 2.0.5.3 (no replies)
I had this same issue with Marlin 1.1.9 ages ago and finally gave up on it. Just updated to 2.0.5.3 and decided to revisit it. As the topic states, unified bed leveling stops after the first mesh...
View Articleissue in Pneumatic Extruder with Baricuda option (no replies)
Dear folks, Even though i have enabled the Baricuda option as below and Connected the HEATER_1 to the pressure valve solenoid, but after first open and close operation, it didn't work. Now struggling...
View Article