Error E1 heating failed when I try to reheat it. (no replies)
I got a message "Error E1 heating failed" when I heat E1 wait if for cooling down and start heat it again. Issue: 1. I start to heat E1. E1 has a temperature of 210 C that is looking fine. I have to...
View ArticleK-factor Calibration Pattern missing Fan control (no replies)
Hi, not sure where to put it so here it is: Marlins K cal pattern is missing fan control I have been playing with it today and noticed that there is no way to set fan. Might be good idea to add it...
View Articleintegrating arduino code into hotend loop (no replies)
Hey all, I'm trying to get some code to run when the hotends hit a certain temperature and am after some advice. I thought what I'd done below would work but I guess I have the logic wrong as It...
View Articleoverride bed temperature limit without having to set everything up again? (no...
Hi there, I built P3steel few years ago and it works like a charm. The firmware is also few years old and i know i should update. :) I will, when i have time to figure out all the steps/mm and endstop...
View Articleusing arduino with marlin 1.1.9 (1 reply)
Using arduino 1.8.9 with marlin 1.1.9 for my anet a8 3d printer. Been using arduino with marlin for some time now. I must have edited something and made a mistake (key stroke) and now am unable upload...
View Articleusing double driver for y axis (2 replies)
i have ready ramps 1.4 with drivers, motors etc and i wanna use what i already have. i wanna use only 2 axis (with laser engraver attachment) but 3 drivers. 1 for x and 2 for y. there is x, y, z, e0...
View ArticleMarlin 2.0x compile issue (odd) (5 replies)
I was makign some subtle changes on my print.. moving the Endstops form max to min, correcting the Stepper motor setting.. I had compiled it 3 times.. worked fine on print. I when to recompile for a...
View ArticleZ after homing (no replies)
I am confused again. Maybe someone has figured this out already. I'm talking bigfix 2.0.x 64876f7 For Configs there is; //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (mm) Backoff from endstops after...
View Article10kHz" messages (2 replies)">Linear Advance debug receives "Acceleration limited" and "eISR running at >...
I'm currently trying to set up linear advance on marlin. I have a print acceleration of 2400. My extruder accel is 5000 and the e steps are calibrated. I'm also using 32 microstepping on the extruder....
View ArticlePrusa i3 rework (emotion tech) and Marlin 2 (no replies)
evening everyone, did anyone successfully put Marlin2 on a prusa i3 rework 1.5 (with a Z axis fixed EZABL probe) ? tried various approaches with the configuration.h: - from the default marlin2 config,...
View ArticleBabystepping display digits (no replies)
Previous builds displayed Babystep with 3 digits .xxx which was perfect - it is BABY steps after all. Now it is showing xx.xxx in the newest release. While looking for something else I stumbled upon...
View ArticleClik here to view.
serial communication RUMBA to NANO (no replies)
HI, how do I set up serial communication in Marlin configuration ? Marlin Bugfix version 2.0.x. RX_TX.PNG Arduino NANO digital pin 0,1 (RX,TX) to RUMBA digital pin 15,14 (RX3, TX3) Thanks.
View Articlecustom lcd menu (no replies)
hi. i`m want to get rid of al the menu option exept moving my axes en print from sd i`m using the marlin 2.0 firmware for my cnc so i don`t need al the menu options can anybody help me greetz...
View ArticleMarlin 2.0.5.3 Configuration questions (1 reply)
Hi All, I am migrating from Marlin 2.0.2 to 2.0.5.3. At the same time I am adding a Z Probe and the bed leveling. I went through and confirmed it would compile prior to installing on my machine. I...
View ArticleDoes multi nozzle duplication work in marlin 2? (no replies)
Hi everyone!! I made a 3d printer with 2 nozzles and a single X carriage, so both extruders moves in unison, and works pretty good. I installed Marlin 2.0.5.3 with Arduino ATMega 2560 and Ramps 1.4....
View ArticleMarlin 2.0.5.3 delta printer bed probing serious issue (no replies)
Hi guys, I am in the process of modifying a FLSun QQ-S delta printer to use a SKR mini E3 board for its sweet silent drivers. This far I adapted and compiled the firmware to include bed leveling with...
View ArticleSKR 1.4 (Turbo) no USB connection with RepetierHost (1 reply)
I have recently switched from RAMPS to an SKR 1.4 Turbo and my serial connection is not working. I tried macOS 10.14 and macOS 10.15 for the host OS. The same configuration worked without issues on...
View ArticleTemp Error/Temp Offset Migrate between Boards via Marlin firmware builds?? (2...
My understanding was that each new Marlin firmware .bin build and flash (especially with M502+M500) flushes out any previous errors or conditions, but I had a MAXTEMP E1 error reboot/reset loop...
View ArticleGraphics LCD on CR10S Pro (no replies)
In the configuration.h file, when defining printer as a CR10S Pro it says "Graphics LCD Requires soldering R64 and R66". Can some one explain to me why this is a requirement?
View ArticleMarlin and TMC2208 on a MKS Gen L Weird Problem (no replies)
Hello I have a custom AM8 printer which i used for the past 2 months with Marlin 2.0 TMC2208 in UART mode, at 24V on a MKS Gen L. I was using a cheap step down converter to power a 12V fan, wich...
View Article