Z will not go Up (1 reply)
Ok I am no stranger to Marlin and how it works.... there is no lines for fixing this Issue 2 things the Z tends to Jam and it will only go Down... Early versions of Marlin had a way to correct this...
View ArticleWhat is wrong with this picture? (no replies)
Marlin ver bugfix 2.0.x.8cfcabe Repetier v2.1.6 I home all with G28. Home is set to backoff 30mm I then run this script g0 x50 y50 ; place XY on bed g28 z ; home Z and raise to 30mm (backoff) g0 z0 ;...
View Articleconfusing documentation (1 reply)
So what is new? I have a nozzle mounted piezo probe/endstop == NOT carriage mounted, The Nozzle IS the probe. based on this excerpt from configuration.h, I should enable both FIX_MOUNTED_PROBE and...
View ArticlePOWER_LOSS_RECOVERY error (no replies)
Hi, I'm trying to enable the POWER_LOSS_RECOVERY feature but it's not working well. Unfortunately, changing the status of pin 31 to HIGH stops printing and restarts and resumes the message....
View ArticleZ-probe "Touch-MI" (1 reply)
HI, I use a Z-probe type Touch-MI Probe by hotends.fr info: Touch-MI probe When using the POWER_LOSS_RECOVERY function, the probe is deployed when restored because the extruder moves to the X_MIN_POS...
View ArticleBTT SKR 1.4 Turbo, BTT TMC2209 Drivers, Sensorless Homing Issues (no replies)
So have a new bigtreetech skr 1.4 turbo with bigtreetech tmc2209 stepper motors. Trying to setup sensorless homing however my Y MIN Endstop always shows triggered which means it never tries to home Y....
View ArticleSKR 1.3 Marlin Build Help (no replies)
Hello, I'm busy trying to do a Marlin build for my SKR 1.3 board but can't get it to build. I was wondering if anyone might be able to help me out? The printer I'm doing it for is a JGAurora A5s with...
View ArticleFirst Layer Fail Using Bilinear Auto Bed Leveling Marlin v2.0.5.3 (no replies)
First layer is high on one side of the bed and low on the other after impleming auto bed leveling. Here's the matrix: Bed 60C SENDING:G29 V4 Bilinear Leveling Grid: 0 1 2 3 4 0 +0.002 +0.112 +0.197...
View ArticleKein Return nach Filamentwechsel (no replies)
Hallo Leute mein BQ Hephestos 2 läuft mit der Marlin 1.1.x toll , aber ! der Filamentwechsel mit M600 im gcode aus cura funktioniert, aber nach dem Laden des neuen Filament steht der Drucker still, am...
View ArticleABL Fail Bilinear. (no replies)
Hello everyone. I have a z-probe problem I cannot figure out. I have read all the post I could find related to my problem with no luck. My Machine: DIY 3d printer running the lastest release of Marlin...
View ArticleClone prusa z-axis rate and steps issue. (no replies)
Greetings. I am a novice. Just built first 3axis prusa clone Reprapguru brand Having trouble with z-axis trabel and rate of travel. Homing works, print starts, extrusion looks good. The layers start...
View ArticleTMC2130 - Marlin - Sdcard (no replies)
Hi, apologies, not sure which section of the forum to drop this into. im using an trigorilla 1.1, marlin 2.0.4.4, tmc2130 i3 clone and it has the discount controller with 2 cables, sdcard and lcd. to...
View ArticleDual Extruder PID (no replies)
Hi, I have a custom 3d printer with a dual extruder. The problem is that I only can use the first one because the temperature of the second one is not enought estable. The extrutders are identic....
View ArticleProblem with RepRapDiscount Smart Controller - Marlin (no replies)
Hi, I have self-made 3D printer assembled and I started to configurating Marlin. I have issue with RepRapDiscount Smart Controller, more precisley with launching it. I've configurated Marlin by...
View ArticleAre you supposed to see z-axis changes mid print with ABL? (no replies)
I've recently got ABL working with my Anet A8, and the prints are coming out great, but when I'm doing prints on pronterface I don't notice the z-axis height changing as it goes around the bed,...
View ArticleBL Touch homing nozzle smashing into heatbed (no replies)
I added BLtouch and upgrade firmware. Now it looks like BLtouch doesn't work. It doesn't do nothing when I press probe, it smashes nozzle to the heatbed. I have uploaded firmware for Z homing....
View ArticleAnalog Input on MKS Robin E3D / STM32F103RCT6 (no replies)
I tried to setup the analog pin 11 -> pc1 -> phys. pin 33 as input. "Hijacked" the PC1 Pin from the Beeper with the breakout board from the bl-touch right at the exp-connector on the board....
View ArticleG29 returns OK but does nothing (1 reply)
I have an Ender 3 Pro with a BTT SKR 1.3 control board with TMC2208s and a BLTouch. I recently had some problems with an older version of Marlin 2.0.bugfix, so I updated it to 2.0.x. Since then, I am...
View ArticleAdding additional axes to Marlin (no replies)
Hi All, I have question. I am currently designing a tool changer upgrade. This tool changer has a elevator mechanism to elevate parked tool heads to maintain the usable print area. The elevator is...
View ArticleInterfacing with the Wanhao i3 LCD (1 reply)
I have a Wanhao Duplicator i3 aka Monoprice Maker Select V2.1, which uses a Melzi controller board. I have successfully installed Marlin to that board, and it functions well. I'm replacing the Melzi...
View Article