X/Y movment minimum speed is limited (no replies)
Hi all ! I'm having problem with delta machine.The X/Y movment speed cannot be less than 600mm/min,and z-axis is ok. I use SKR PRO V1.1(STM32F407) board to build. I did some tests. 1. mega2560 is ok....
View ArticleAuto fan configuration issue on MKS GEN L V2.0 (no replies)
Hello, I am trying to use pin 9 for the E0_AUTO_FAN_PIN and I keep getting the same error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN." I changed the value of RAPMS_D9_PIN to -1 in the...
View ArticleMarlin 2.0x no longer builds in OS X (no replies)
I've had zero issues for 2 years and all of a sudden I can't build Marlin anymore. I spent nearly 5 days straight trying to fix this, hoping someone here can shed some light. OS: Both Macs are running...
View ArticleSerial Communication between Anet V1.7 board and ESP32/Nextion display in...
Hi! I would like to connect Anet A8 Plus to Wemos R32 and send some information both ways. Is it possible? How to do that? Where i can find any informations where i can add my code (eg. If something...
View ArticleMarlin 2.0.5.3 Z height issue. (no replies)
Hi, I set the Z-offset to my proximity sensor with M851 Z0, G28, M211 S0, move nozzle down, M851 Z-xxx M500, M211 S1, G28 and, on the display, Marlin reports the right figure. However, when I start a...
View ArticleSKR 1.3 "multi" neopixel (no replies)
Hi, I'm working with SKR1.3 and FYSETC 12864 v2.1 display (neopixel version) and found out that having this display enabled, will result in having all the neopixel set up limited to pin EXPA1_05_PIN....
View ArticleNeed help with Z axis offset issue after auto leveling. Marlin V2 (no replies)
Hey peeps! I have a P802ma (ANET A8 clone) that I updated the firmware from Marlin 1, to Marlin 2.0.x (latest). And I've been trying to get all the kinks worked out. So far I have everything set up to...
View ArticleLooking to Echo Serial 0 to Serial 2 - Marlin 1.X (no replies)
Hello, I'm looking to control my printer via USB with a host program, but I would also like to read values over serial on a second device. More specifically, I would like to parse an M114 command for...
View ArticleOctoprint bed heating kill called (no replies)
What is the problem? Trying to print on my CR10v2 and SKR 1.4 Turbo. I have the bed temp set at 65, but it heats up to 55 and just stays there. Eventually I get this error: “Your printer’s firmware...
View ArticleHow to use Serial object at Marlin 2.0.x (SKR v1.3)? (no replies)
Hi, after several days trying it and reading a lot i need some help... I'm upgrading a Anycubic Chiron from Trigorilla (8 bits) to SKR v1.3+TMC2208 (32 bits) and I want to use stock display from...
View ArticleZ axis stopped moving (no replies)
HI everyone! I am setting up a CoreXY printer with a SKR 1.4 board paired with TMC2209 drivers. And everything was going smoothly (x,y,z were working perfectly and E0 was next to be calibrated) when z...
View ArticleBTT SKR 1.4 Part Cooling Fan Configuration (no replies)
Thank you for accepting me into your forum. I have recently fitted a BTT SKR 1.4 Turbo motherboard to my printer. I’ve got everything working except for the Part Cooling fan which doesn’t turn when...
View ArticleNew board on marlin 2.0 (6 replies)
Hello, i am trying to add a new board in marlin (ATmega2560) but i can’t seem to even compile it. i start clean from bugfix-2.0.x branch and then i do exactly what the documentation says: “Once your...
View ArticleLayer height value does not rise on display during print (no replies)
Hi, I recently upgraded my ender 3 pro with SKR1.3 board and Marlin 2.0. The printer works perfectly without any stepper problems, the upper layers also printed as it supposed to be. However the layer...
View ArticleXY axis moving very slow to Z home or Auto level (1 reply)
Hi, I am building my own 3d printer and am using Marlin bugfix-2.0x. XYZ axes move ok, both ways. XYZ axes will all home ok. I have installed an inductive probe for ABL (auto bed leveling) - works...
View ArticleCompile with Arduino and get error (2 replies)
I compile a week old bugfix 2.0.x and everything is good. I try to compile today's bugfix with my config files and get this: Archiving built core (caching) in:...
View ArticleWeird problem with extruder temperature (no replies)
So I'm running marlin 2.0.5.3 on a prusa steel and for a couple of weeks I've been having this issue. It's best described with the video below. I changed the thermistor I tuned the pid but I don't...
View ArticleHoming issues (no replies)
I have an Anet A8 with SKR 1.4 turbo board with TMC 2209's and sensorless homing, TFT35 display and the latest Marlin 2.0.x bugfix Marlin installed. I have several problems/things not working properly...
View ArticleRepRap full graphic with MKS Gen L (3 replies)
Hi first time poster here, I have a Anet A2 plus that I successfully upgraded to Marlin so I could enable thermal protection and mesh bed leveling. While upgrading the hotend I managed to damage the...
View ArticleUBL seems off (no replies)
I'm trying to get UBL working with a BLTouch probe. I have the probe working, and homing works. I can also run the UBL mesh probe and get what looks like reasonable results. However, when it's active,...
View Article