"bugfix-1.1.x" and "Viki2" not working (no replies)
Hello everyone, I wanted to change my firmware from Marlin-1.1.4 to Marlin-1.1.6, but it will not compile (cant remember the error). So I decided to use the most current (downloaded today)...
View Articlemotor being hotest (no replies)
Hello every body i hope someone could help me i have my own 3d printer and i work with Marlin1.1 firmware, now i pass some problem like vibration without rotating and now the motor is working but it...
View ArticleI want to learn how pause process works (no replies)
I want to learn how pause process works, because I want to eeprome it then power the printer off and power it on again then continue printing. Where can I lean that process ? If from marlin where...
View ArticleMK2 Multiplexer Confirguration Help (no replies)
Can someone point me to a URL where I can review the setup procedures for MK2 Multiplexer utilization I'm attempting to configure in Marlin 1.1.6. I've un-slashed the "#define MK2_MULTIPLEXER" and...
View ArticlePin D2 and X motor driver steps (no replies)
I'm trying to get a laser diode working with my Tevo Tarantula. It's running a Biqu MKS Base v1.4 with Marlin. I spent quite a bit of time trying to get PWM control working; ended up using the X+...
View ArticleUnderstanding XY resolution (no replies)
Hi, I have built and been running successfully a home designed reprap cartesian printer based on a Gen 7 main board with Marlin 1.1.x firmware. I have been looking to improve the resolution on my X...
View ArticleStrange behaviour with RepRapDiscount Full Graphic Smart Controller (Reset...
I trying to use a "MKS Base V1.5" with a "RepRapDiscount Full Graphic Smart Controller". The Marlin firmware appears to be ok on MKS, Can see the temperatures by serial, stepper motos also works. Even...
View Articlesetting up Bltouch in marlin (no replies)
You'll all have to forgive me because i'm sure that this question gets asked frequently, but i've been searching around for several hours now and i cant get this figured out. I'm setting up a bltouch...
View ArticleMarlin 1.1.7 not booting after restart (no replies)
Hey there, i have a strange behavior with Marlin 1.1.7. I flashed 1.1.7 to my printer, Marlin starts and everything is fine. But if i shutdown the printer an restart, then the display is empty and...
View Articlecompiling error need help (no replies)
hey guys i got my Config H ready and when i go up upload i get this #error "Pins for this chip not defined in Arduino.h! If you have a working pins definition, please contribute!" but im using an...
View ArticleMarlin as Scara Robot Arm Firmware (no replies)
Hello, I've seen someone post marlin as firmware for a scara arm robot. I know how this works with a 3d print but I was curious if someone can point me to some resources that would help me modify the...
View ArticleMultiplexing SPI "Chip Select" lines (no replies)
Hello everyone. I have an Azteeg X3 PRO motherboard, with a Viki 2 LCD display. Currently I have 6, TMC2130 stepper drivers installed. All of the drivers are using the SPI interface to set the...
View ArticleArduino DUE + RAMPS + FULL GRAPHIC LCD on Delta Stuttering (2 replies)
I have a little probelm with my beloved Anycubic kossel linera plus (Delta) printer. It could print smoothly with it's original ATMEGA 2560 based trigorilla board with 2004 LCD. But I upgraded it to...
View ArticleSkew Correction in Marlin 1.1.7 (no replies)
Does skew correction only correct during delta calibration / bed leveling or also correct skew when printing parts? I dont know how to activate this feature. In console: M852 Outputs: Skew Factor XY:...
View ArticleMinimum X not zero, but it is set to 0 (1 reply)
Hi, For some reason my X-axis has a minimum position of 10 instead of 0. My limits are set as follows #define X_MIN_POS 0 #define X_MAX_POS 317 But after homing I can move in the range [10..327] I...
View ArticleTravel very slow (no replies)
Am running Marlin (2 weeks old git clone) on a minitronics board. But every time the head needs to travel and not print on the x&y axis it does this with 0.1mm/s (guess). Am really puzzled by this...
View Article3D Printer RAMPS 1.4 SD Card Reader (no replies)
Hello; I have purchased replacement 3D Printer RAMPS 1.4 SD Card Reader and need some help. I have a Ramps 1.4 compatible controller and a RepRapDiscount Smart Controller working. Asking for help to...
View ArticleMixed Bed leveling possible? (UBL and manual) (no replies)
Dear all I'm retrofitting a printer with a BLTouch probe and have a question concerning the bed levelling with UBL. The printer bed can be levelled using three thumb screws. Originally the bed was...
View Article1.1.7 after auto home / bed leveling raises Z 10mm:( (3 replies)
So I just got 1.1.7 working after upgrading from a 1.0.x version. I'm finding it very annoying that after performing auto home or bed leveling that the Z-axis raises 10mm. Is there a quick fix for...
View ArticleThermistor selection (no replies)
I have a SEMITEC 104NT-4-R025H42G screw in type thermistor on my hotend. I dont see that on the thermistor table to select so I used type 5 104GT-2 with Marlin 1.18 Googleing about a bit I am pretty...
View Article