Flsun Delta Kossel W/ Marlin 1.1.6f-AC FW not leveling properly (no replies)
Hi everyone, this is my first post here. I'm helping a friend fix his Flsun Kossel Delta. We never could get it to work properly, and the fact that it shipped with the wrong firmware is probably why....
View ArticleUser Error? Endstops don't work (no replies)
So I'm sorta at wits end here.. I'm definitely new to building a printer, so that could be it. Here's the situation: I have a chinese RAMPS v1.4 + arduino + LCD. I flashed it with a mostly...
View ArticleMotors Off after 2 mins ? (no replies)
I've just upgraded from Marlin 1.1.0-RC3 to 1.1.8 and I'm getting some sort of timeout occuring. I home all axis and then after approx 2 mins the motors switch off and the display shows flashing '?'...
View ArticleThermistor/LCD Display shows opposite change in temperature (1 reply)
Has anyone ever experience an opposite temperature change readout from a thermistor connected to Ramps 1.4 running current Marlin? Marlin 1.1.8 Arduino Mega 2560 R3 Ramps 1.4 12864 LCD w/SD Card...
View ArticleCBot Marlin to 'mainline' marlin 1.0 or 1.1 (no replies)
I just got a 3d printer by Createbot, a Prusa i3 clone, that I have their firmware for (albeit it was broken as sent to me and I had to fix it to get back to square one), and it works, but I'm...
View ArticleX offset between nozzle and start bed (no replies)
Hello, i've a question about bed area (sorry for my english) when my head (with nozzle) make homing on X axies, it push the min_endpoint swith and marlin configure it's 0 x axies, it's normal. Marlin...
View ArticleHeating problem during printing (1 reply)
Hi, I am using Marlin 1.1.8 Heating is just fine when the printer is idle and I tuned the PID parameters. I also tried extruding a quite amount of plastic and temperature dropped just 4 C before...
View ArticleTrying to setup a BLTouch and failing (no replies)
Happy New Year! I've been banging my head against the wall trying to get my BLTouch setup. This is what the terminal on Octoprint outputs when I start up: QuoteRecv: Error:STOP called because of...
View ArticleOdd inductive sensor triggering issue - z axis min (1 reply)
So, if I home through the smart controller display in the "prepare" menu, everything works normally and correctly. Everything homes then I can bed run the "bed leveling" and that works normally as...
View ArticleMarlin 2.x help or other recommendations? (2 replies)
Hi guys, I've just built a corexy machine from scratch and am in the process of doing the electronics. I started off with an arduino mega and ramps board running marlin 1. And all went well for...
View ArticleIs it necessary to enable PID for the heat bed? (2 replies)
I'm trying to upload the new marlin firmware to my board but I'm getting an error:- Arduino: 1.8.5 (Windows 7), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)"...
View Article1.1.8 Homing correctly but not when running print (3 replies)
Hello, i decided to update my firmware today in my CR-10S to accommodate a Z probe in the coming days so, after downloading and following a few youtube videos the printer started with the new marlin...
View ArticleDisabling Z home double bumping in Marlin 1.1.8 (no replies)
Since using a piezo sensor, I want to disable the double bump feature of Z homing. I've already increased the double bump speed (piezo requires certain speed to make sure it triggers) by setting...
View ArticleA problem with Atom (no replies)
I'm using an editor/compiler called Atom. I've recently downloaded Marlin 1.1.8. I am having difficulty with the platformio.ini file that I do not know how to fix. In the new file there is a new...
View ArticleNo power to Z-axis in Marlin with TCM 2130 Drivers. (no replies)
I'm stuck... I am sure the problem is something simple that I am missing, I recently switched from Repetier to Marlin to take advantage of the TCM 2130 Drivers. All of my electronics (Arduino...
View ArticleFree xy problem (delta printer) (no replies)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer) (no replies)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer) (no replies)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer) (no replies)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer) (no replies)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View Article