Autolevelling z_probe_offset what is this value used for? (3 replies)
The value in autolevel settings Z_PROBE_OFFSET_FROM_EXTRUDER what is it actually used for? The reason I ask as it does not seem to make any difference what value I enter here. After homing z with my...
View ArticleClik here to view.
Manual Mesh Bed Leveling On UM2 Go Clone Issue :S (4 replies)
image2.jpg So I recently built an UltiMaker 2 Go clone with Marlin 1.1 RC3 and everything is working pretty great. I wanted to do manual bed leveling for the time being but I'm running into an issue....
View ArticleInductive Sensor without Inductive sensor adapter (2 replies)
Hi All, I have build my 3d printer and want to install also a inductive sensor. I have the following inductive sensor: DC 6-36V 300mA NC 3 Wire 2mm Inductive Proximity Sensor Switch LJ12A3-2-Z/AY Do I...
View ArticleMKS Base V1.2 Using RC4 Does not Boot (1 reply)
I've tried defining MOTHERBOARD with the following: BOARD_MKS_BASE, BOARD_RAMPS_14_EFB, and BOARD_RAMPS_13_EFB (equivalent to 33 which I am using fine with 1.0.2-1) with no luck. Display just shows...
View ArticleMarlin RC-4 (Release Candidate #4) Frozen and Released (no replies)
Nearly everything is A-OK! The code is getting very solid. Give it a try!
View ArticleRC3 to Rc4 Autolevel Grid wrong (5 replies)
So I was running a SmartRapCore Alu on RC3 with no issues, decided to try Rc4 (why I hear you ask if you have no issues...) anyway Everything so far normal except when I send G29 my bed level grid...
View ArticleSecond extruder won't stop overheating (no replies)
I added a second extruder to my Mendel 1.5 and it won't stop heating. I am using a RAMPS 1.4 with Marlin 1.0.2-1. When I open Pronterface it registers the second extruder and shows the ambient...
View ArticleCustom Lidar Endstop (1 reply)
Hello, I am currently trying to configure my CNC machine to use a Lidar sensor as an endstop. What I am trying to do is figure out how to trigger the endstops once the distance has changed. That way...
View ArticleMarlin loads on lcd but not pronterface (2 replies)
This is my first time trying Marlin. I have uploaded the firmware to my board but when I try to connect to my printer in Pronterface it just stalls on connecting. However everything appears to load...
View ArticleFirmware problem (we assume) - bed and extruder not responding to Repetier...
Hello, we are a makerspace in Lahore, Pakistan and we are using a custom printer from AB3D. Unfortunately we have a hard time getting it to run. It uses the RAMPS 1.4, Marlin and Repetier Host. Motors...
View ArticleRumba v1.2g, E3Dv6 hotend, TEMP_SENSOR_0=5... still wrong temperature (no...
hi some advice appreciated: i'm doing a corexy folding printer, and using a Rumba v1.2g with an E3Dv6 hotend. the configuration page for E3Dv6 says use TEMP_SENSOR_0=5, which i'm doing... and the...
View ArticleZ axis doesn't moving up when printing (no replies)
Hello, I've got a little problem here. I've test my axis in manual control and everything runs perfectly, but when I start my printing, the z-axis doesn't moving up at all. I've read a post in this...
View ArticleMarlin Compiling Errors (no replies)
Up until now, I've been running my first printer-a TEVO Tarantula-with stock, unedited firmware, and I'm trying to implement some much needed changes. After a good amount of searching, then finally...
View ArticleMarlin RC5 - MKS_13 vs MKS_BASE (1 reply)
Why was MKS versions 1.3 and 1.4 separated out in RC5 from MKS base (earlier versions)? I cannot see any difference, perhaps coming? MKS_BASE was worked for me.
View ArticleError with u8glib when compiling for LCD support SOLVED (3 replies)
I setup my firmware in marlin (latest version) and when I set it to compile it tells me to download the u8glib for arduino libraries. So I download this: and put it in my documents/arduino/libraries...
View ArticleProblem using M42 (no replies)
I'm trying to add bed lights to my Ord Hadron printer using a Reprapdiscounts fan extender (http://www.geeetech.com/wiki/index.php/Reprap_Ramps1.4_RRD_Fan_Extender). A test program blinks the lights...
View ArticleMesch_bed_leveling not working from LCD "Bed level" (1 reply)
I have up-loaded the newest Marlin 1.1.0 RC5 software with activated the "Mesh_bed_leveling " and "Man_bed_leveling " in the configuration.h file. When i uploaded it with Arduino IDE_nightly (= 1.6.8...
View ArticleDisable Z Probe (2 replies)
After dealing with an inductive Z probe that returned imprecise results I switched to manual bed leveling on my Printrbot Simple Metal and removed the errant sensor. I'm worried that if I accidentally...
View ArticleHardware Serial2 in Marlin (no replies)
Hi, I am building a SLA 3D printer [www.kvistholm.se] Using a LCD display and a displaydriver (http://www.abusemark.com/downloads/dpadapter_rev1b.pdf) To turn the display on and off is a crucial in my...
View ArticleM565 in Marlin 1.0.0 (no replies)
I have Marlin 1.0.0 on a Robo R1+ and M565 returns -0.7 is that stored in EEPROM somewhere? I don't see a default value for it in configuration.h but M503 does not display anything with -0.7 when it...
View Article