changing oversampling (no replies)
i recently changed my printer's sensor to thermcouple and i'm pretty satisfied with it's high temp durability but on the other hand, it seems like thermocouple is very volunable to noises. my temp...
View ArticleClik here to view.
software problem: target temperature not reached (no replies)
I have a problem where the software sets the temp of the hot-end to about 10 degrees C below the target the g-code specifies. This is consistent when set to low or high temps. This is an image of a...
View ArticleNeed help installing 12864 lcd on Cr-10s PRO. (no replies)
Hi trying to post a post here. I have a Cr-10s PRO. Fantastic machine but lousy firmware and display at the moment. Seeing more have switched to Marlin 1.1.9 and using 12864 display similar to Cr-10s....
View ArticleDual Extruders and move axis operation (no replies)
I am building my 3rd custom 3D printer, but this is the first one I've done with dual extruders. I got the printer powered up and running for the first time last night, but I have some questions on...
View ArticleInductive probe does not trigger on marlin 2.0 bugfix skr 1.3 board (no replies)
Hello I have a problem with inductive probe. I had it working before but now i upgraded to skr board and it doesnt trigger. I switched off pull up resistor, Probe sends signal because if i put it into...
View ArticleUsing timers/delays in the firmware to change "configuration" parameters (1...
Hello all, I was wondering if there is anyone that has experience implementing delay/timer functions to modify Marlin code, specifically in 'configuration.h"?? I would like to say, after 100000ms...
View ArticleAuto Bed Leveling Issues (no replies)
I think I might be having some leveling issues using the BLTouch. It appears as if it's not working. I have Marlin 1.1.8 on a D-Bot CoreXY machine. The reason it caught my attention is that I printed...
View ArticleUpgrading configuration.h and cofiguration_adv.h (1 reply)
Hello, I'd like to upgrade my clone Prusa i3's firmware, by myself, because the producer is not supplying the new Marlin files :) so I downloaded the 1.1.9 version and opened comparison mode on npp...
View ArticleSD position and pause print (UPS, recovery after power loss + octoprint) (no...
Hello, I am currently developing a plugin for octoprint, to add the management of an UPS and I set up a system of recovery after power loss. for that I put the print in pause and I recover the...
View ArticleSanity check: z-min? (no replies)
Just wondering if sanity checks for z-min exists in 1.1.9. z-min error my prob be normally closed, only opens when it touches the bed, so before a bed level is executed, check if prob signal is...
View ArticleCR-10 S4, Marlin firmware 1.1.9 bugfix, extruder temperature not...
We got a CR-10 S4 and are trying to replace the built-in manufacturer firmware which crashed all the time (if you tried to move an axis more than 10mm at a time it would hang requiring a power cycle)....
View ArticleMarlin 2.0.x delta printer auto bed level issue (no replies)
Hi all, I have this issue after updating to the latest version. I checked forums for a solution but found nothing that work. I have a log of the auto-level debugging and config files that I include...
View Article_draw_chamber_status definition in wrong place (no replies)
Hello, I’m working on setting up chamber temperature control in Marlin 2.0-bug fix. When enabled, I get a compiler SegFault in Arduino GUI, so I rebuilt it in PlatformIO (a much nicer experience). The...
View ArticleProblems compiling... Help! (no replies)
I have a Creality Ender 3 with a MKS Gen L main board and I'm wanting to use the TMC 2130"s in SPI mode. When I try to compile the code I get this error: Any help on what I'm doing wrong? Marlin 1.1.9...
View ArticleG33 probe suggestion (no replies)
I have an offset bed probe, on my printer an IR one. But my one problem with the G33 routine, is that it does not take into account the offset of the probe, and I assume there is a reason for this, if...
View ArticleGetting a "Deploy Z-Probe" message when trying to auto bed level (no replies)
I am new to 3d printing and I am running Marlin 2.0 on a SKR V1.3 board on a delta Kossel plus (just upgraded from the trigorilla board) and I am getting a message: “Deploy Z-Probe” when I try to do...
View ArticleMarlin 2 prints on air (auto leveling issue?) (1 reply)
Hi guys, I've installed marlin 2 on a azsmz mini and all seems to run OK, so just tried to do the first print but the print starts way above the bed surface, at z15, on the file I tried to print there...
View ArticleArduino Due + RAMPS-FD + TMC2660 SPI communication problem (2 replies)
Hi! I used Arduino Due + RAMPS-FD-V1 + TMC2130 Driver boards for all X, Y, Z and E0 with SPI communication mode and I used Marlin bugfix-2.0.x version FW code. I used software SPI mode...
View ArticleMixing Feature with 2 Independent Heaters (no replies)
Hello, I am in need of some help. I need to be able to have the ability to have 2 heaters that can be set at 2 different temperature and still be able to use the mixing feature. It only allows me to...
View Article