Acceleration and feedrates (2 replies)
I use slic3r pe almost exclusively. In the machine limits section slic3r is expecting mm/s². Marlin itself has these values in config.h as mm/s. Haven't been able to find a direct conversion from mm/s...
View Articlereadout Marlin by using MYSERIAL1 (Nextion Display) (no replies)
Hi, im about to set up an Nextion Display to my IDEX Printer. I let Marlin show Temps an positions via MYSERIAL1.print("Homescreen.E0.txt=\""); MYSERIAL1.print(Temperature::degHotend(0));...
View ArticleImportance of NO_WORKSPACE_OFFSETS? :S (1 reply)
Hi all I'm trying to compile a Marlin 2.0.x build for my Creality Ender-5 with BLtouch upgrade. This printer uses a ATmega1284P chip, with small 130 KB of memory. So after disabling the same features...
View ArticleMarlin 2.0 compile error (no replies)
Trying to compile Marlin 2.0 for my RAMBo and Reprap discount Full graphic smart controller.. I changed the Mother board and commented the LCD screen.. when I try to compile here is the error list::...
View ArticleProblem trying to update my software (2 replies)
I am trying to update my Marlin equiped printer .The update is from Github for my German Rep Rap Protos V3 . I try to run it through the check upload and get ,expected primary-expression before...
View ArticleMarlin 2.0.2 compile error (1 reply)
Hello all Wondered if anybody else had had this issue that Marlin 2.0.2 wont compile due to the following errors? In file included from Marlin\src\module/stepper.h:47:0, from Marlin\src\Marlin.cpp:37:...
View Articlegeeetech i3 pro c marlin 2 configuration (2 replies)
Is there a configuration file for the geeetech i3 pro C for Marlin 2.x ??? I'd like to upgrade but modifying the config file for v2 is rather daunting and a good starting point would be a useful...
View ArticleG29 options not working (no replies)
G29 works well in my setup but "G29 P4 S6000" gives the same results as a plain G29, which is a 3x3 in my case. The options seem to be ignored. Is there something in the marlin firmware that can cause...
View ArticleUBL G29 J Question (no replies)
Hi, is there a way to specify which three points are being probed when using G29 J ? I would like to use three particular points.
View ArticleUneven Z motors speed - lead to X carriage not straight (no replies)
Hi all, I have a problem with my printer. It's a custom P3Steel 30x30x20, with a SKR 1.3 / TMC 2208 UART / Marlin 2.0.2 (updated few days ago), with 1 stepper motor for Dual Z axies motors, in...
View Articlegeeetech i3 pro c marlin 1.1.8 "Filament out" configuration (1 reply)
Hi, I am trying to setup a filament out sensor on my Geetech i3 pro C running Marlin 1.1.8. I believe I have made all the required config changes but M119 only displays X/Y/Z_MIN status and not X_MAX...
View Articlehelp configuration marlin 2 bed level lcd (no replies)
hi I need some clarification if possible I have been trying to study and compile marlin 2 for just over a month, I am a novice I can't understand what I have to comment or uncomment or write in order...
View Article2.0.x HotEnd Temp Plummets Before Print (no replies)
I've been having issues with my Printer lately, and it's starting to frustrate me. My printer is a Modified Ender-3, with an SKR v1.3 Board, Micro Swiss All Metal, Semitec 104GT Thermistor, TMC2130s...
View ArticleDoes Marlin support UART Multiplexing? (no replies)
Hi, does Marlin support UART multiplexing for the stepper drivers, because some of the trinamic ones uses uart, like the RepRapFirmware? The Duet Maestro (which has the RepRapFirmware) does it.
View ArticleStrange x-axis problem using Marlin 2 (no replies)
Using Marlin on a CNC build. Was using Marlin 1.1.9 via Arduino IDE 1.8.10 and all worked OK. But when I try similar config in Marlin 2 the X axis hardly steps (instead of executing say 2000 steps for...
View ArticleCR-10S Marlin 1.1.9 vs TH3D Unified firmware (no replies)
Hi guys, newbie here. So I finally got to upgrading my stock CR-10S firmware to the latest Marlin version (I needed to tune my PID setting for micro-swiss upgrade and wanted to add the thermal runaway...
View ArticleProblems with Marlin 2.0.3 compiling - Mega2560 error (no replies)
Hi, Working on updating home built DIY Mendel Prusa i3 clone with Marlin 2.0.3 and Ramps 1.4 controller. I need some technical help here. On my desktop PC I configured my newly downloaded copy of...
View ArticleExtruder changes direction automatically (no replies)
Hi, I hope someone can help me with the following problem. I am using a Bigtreetech SKR PRO v1.1 board with TMC2208 drivers and Marlin 2.0.x. I used other firmware the bug fix, however they all have...
View ArticleSKR Mini E3 Firmware (no replies)
Whenever I attempt to change the Firmware of my Ender 3 with Vanila Marlin as described by TH3DStudio.com. using VS Code and Platform-IDE. It refuses to create a Firmware.bin file. It will Build using...
View ArticleQuestion about Z speed (no replies)
Hello I have a homemade printer using marlin firmware I'd like to increase fast Z displacements. I'm talking about Z displacements used to approach z endstop. Wich parameters have i to modify please ?...
View Article