Panel buttons don't work (no replies)
The buttons on my control panel either don's work or are unusabley flaky. Pushing the O.K. button may or may not flash the next menu on but only for about a second. On the single occasion that I was...
View Articleerror: Err: Too far! (1 reply)
greetings, just a quick question : after updating my stock A8 to marlin 1.1.9 with the correct configuration profile , after auto home the display shows: X -33 Y -10 Z 0 , and The home position for my...
View ArticleRequest: UBL differential mesh calculation (no replies)
Hi, I could not locate a way to do this automatically, this is why I called it a request. I am adding a set of 3 piezo probes to an Ultimaker clone attached to the print table base plate knobs. Two of...
View ArticleMarlin 2.0.x bugfix on Wanhao D6 Compile Error (no replies)
I have downloaded the 2.0.x version for the wanhao d6 for marlin 2.0.x bugfix and am receiving compile errors when using the example configuration.h and configuration.adv.h. The compile errors I'm...
View ArticleAuto bed leveling don't work in Marlin 1.1.9 (no replies)
Firmware Marlin 1.1.9. After the commands G28 G29 G0 z0 the nozzle does not reach the bed 4-5 mm. I turn on the logging of the G29 command (M111 S32). At the end of the work gives messages for linear...
View ArticleAuto bed leveling don't work in Marlin 1.1.9 (1 reply)
Firmware Marlin 1.1.9. After the commands G28 G29 G0 z0 the nozzle does not reach the bed 4-5 mm. I turn on the logging of the G29 command (M111 S32). At the end of the work gives messages for linear...
View ArticleSSD1306 OLED over SPI with Marlin 2.0 (no replies)
Hello All, I've been using 0.96 OLED display over I2C on Marlin 1.1.9. After having switched to Marlin 2.0 running on Re-Arm I am experiencing issues with this display coonected over I2C. I've done...
View ArticleHeating failed (no replies)
Hello everyone I am building a 3D Printer every time I try to print, The extruder does not heating up "stays at room temperature" , while the heatbed heating up, but after 10 minutes an error appears...
View ArticleProblem z axis (1 reply)
So I have a Monoprice mini v1. The mother board failed so I replaced it with a reprap RAMPS 1.4 board and Arduino Mega 2560 processor. I have compiled and loaded Marlin 1.1.9. The unit appears to home...
View ArticleIssue with Bltouch (no replies)
Ok so here is the deal, I have a Anet A8 and it probes the bed is 9 points.. it's fine nozzle does not crash into the bed and whatever.. however the start of the print where I have it print a 4mm line...
View ArticleDUAL "E" STEPPERS FOR CLAY PRINTING IN MARLIN FIRMWARE (1 reply)
Hello, I`m printing with clay using the E0 stepper inside the extruder head and an air compressor to feed the extruder with clay. I want to replace the compressor with another stepper that pushes a...
View ArticleFANMUX what is it? (1 reply)
So i've been wondering this for a while, what is FANMUX for, I see user after user trying to use these settings to no avail.. I suspect in part as no one seems to know what this is for. It was added...
View ArticleProblem with Z homing. (1 reply)
I just rebuilt a Cartesian printer updating the z axis hardware and upgrading the hot end and extruder. All seems to be working ok, but when I try to jog Z, I want to bring the head down until it's...
View ArticleVibration on X and Y EasyConfig 2.0.X Tevo Tarantula (no replies)
Hi, I have a Tevo Tarantula, was using EasyConfig 1.0.X, so far so good. Flashed the 2.0.X using Arduino 1.8.10. The printer vibrates while printing curves. Tried the official Marlin BugFix 2.0.X...
View ArticleUBL Delta Calibration for Square Printing (no replies)
Marlin 1.1.9 UBL Delta Leveling for Accurate Square 3D Printing Problem: Using Marlin’s UBL for helping with creating a perfect first layer does NOT help overcome the printer’s geometric build...
View ArticleMarlin 1.1.9 su anet A8 leggere i parametri dall eeprom (no replies)
Buon giorno Non so come ma preso da strana ed imprevedibile follia un giorno sfogliando un sito di compravendita mi sono imbattuto in una Anet A8. Ahimè senza avere idea di cosa fosse una stampante 3d...
View ArticleHow to use both micro-switches and TMC2130 StallGuard for end stop detection?...
Hello all - I was reading the forum for several months, but this is my first post here. :) I have just upgraded Ender 3 with SKR1.3 32-bit board with TMC2130 motor drivers (SPI mode) and I use...
View ArticleBed Levelling grid size in Marlin 2.0? (2 replies)
Where do I define the bed levelling grid max/min parameters for Bi-Linear bed levelling in Marlin 2.0? This used to be in Configuration.h in 1.1.x but its not there now in 2.0
View ArticleG0 command issue (no replies)
This is an upgrade to a recent bugfix 2.0.x and it previously worked. If I reset, home all and issue a G0 x150 y150 command the drives buzz, the head goes no place, and the position indicators all...
View ArticlePrinter gets up to temp, but won’t start printing.. (no replies)
Spectrum upgraded my internet service this morning and I had to go through and change all my ip settings. Now I am having a problem starting a print. The printer gets up to temperature, but it never...
View Article